Cleaning And Care; Inspection And Maintenance; Inspections And Maintenance - Samson 40 Serie Instrucciones Para El Montaje, Funcionamiento, Mantenimiento Y Desmontaje

www.samsondoors.co.uk
From outside:
Turn the key 360°
▶
To unlock: turn the key left
To lock: turn the key right
From inside:
Slide the locking lever on the lock
▶
To unlock: slide it upwards
To lock: slide it downwards
5

Cleaning and Care

ATTENTION
Scratches on the panes due to improper cleaning
Rubbing the panes causes scratches.
Dirt and dust particles must first be thoroughly rinsed
▶
off with water. If necessary, only wash with water, a
pH-neutral household detergent and a soft, clean
cloth.
Clear water is sufficient for cleaning and care . Use
warm water together with a neutral, non-abrasive cleaning
agent (household detergent, pH value 7) if more heavily
soiled. To preserve the surface characteristics, regular
cleaning must be carried out at least every 3 months
(outside of door, seals). The slide area behind the side
seals must be kept permanently clean and able to slide.
A variety of environmental influences (e.g. maritime
climate, acids, road salt, air pollutants, paint damage) may
make additional protective coating necessary (see Paint
treatment on page 10).
6

Inspection and Maintenance

6 .1

Inspections and maintenance

WARNING
Danger of injury due to defective safety components
Important safety components may fail or become
defective if not sufficiently inspected and maintained.
Have a qualified person perform inspection and
▶
maintenance work at regular intervals.
The following inspection and maintenance tasks must
be carried out by a specialist in accordance with these
instructions, before initial operation and at least once a
year.
6 .1 .1 Inspect all load-bearing components
WARNING
Danger of injury due to high cable tension and high
torques
Cables and springs are under high tension and torques.
Damaged cables or springs may also cause serious
injuries.
Fix the door leaf to prevent uncontrolled movement
▶
before exchanging damaged cables or springs.
Be particularly careful when exchanging damaged
▶
cables or springs.
3 048 942 RE / 08.2016
www.samsondoors.co.uk
0800 328 6250
Check load carriers (cables, springs, tracks, supports)
▶
and safety devices for breakage and damage,
replacing any damaged components as necessary.
Spring safety device
Check the effectiveness of the detent pawl and the
▶
secure seat of the locking gear (see Fig. 14.3 Spring
safety device).
6 .1 .2 Weight counterbalance
Danger of injury due to uncontrolled door drops
If the counterbalance has not been properly adjusted,
this may result in an uncontrolled door drop, which could
trap persons or objects.
Retension the torsion springs.
▶
High torque
Springs are under high torque stress and may discharge
high forces if they are not secured during tensioning.
Fix the door leaf to prevent uncontrolled movement
▶
before adjusting the torsion spring shaft.
Check the counterbalance of the door leaf
Manually open the door halfway. The door should be
▶
able to hold this position.
If the door moves substantially downwards:
Retension the torsion springs.
▶
6 .1 .3 Fixing points
Check all the fixing points on the door and the building
▶
structure and make sure that all the fastenings are
securely seated and, if necessary, retighten.
6 .1 .4 Rollers and tracks
When the door is closed, the rollers must be easy to turn.
Adjust rollers if necessary. Observe the operator fitting
▶
notes; they contain details on roller adjustment.
Clean tracks, if necessary, do not grease!
▶
6 .1 .5 Hinges and roller holders
Oil hinges and roller holders.
▶
6 .1 .6 Locking cylinders
Damage to the locking cylinders due to unsuitable
cleaning products
Locking cylinders may not be cleaned with agents
containing oil or be oiled.
Only use specialised care products.
▶
Do not use oil or graphite.
▶
6 .1 .7 Seals
Check for damage, deformations and completeness.
▶
If necessary, replace.
0800 328 6250
www.samsondoors.co.uk
WARNING
ATTENTION
www.samsondoors.co.uk
ENGLISH
9