Safety Instructions - Stanley BOSTITCH BT1855 Especificacion Técnicas

SAFETY INSTRUCTIONS

© Stanley Bostitch
m IMPORTANT READ CAREFULLY: It is important that all operators read and understand all sections
of this Tool Technical Data manual and the separate Safety and Operating Instruction Manual which
GB Not to be reproduced without permission. Unauthorised copies of this document do not constitute CE
come with this tool. Failure to do so could result in you or others in the working area to be seriously
compliance for the products.
injured.
FR Reproduction interdite sans permission préalable. Les copies non autorisées de ce document ne signifient en
m WARNING! Eye protection in accordance with 89/686/EEC, and with equal or greater grade than defined in
rien que les produits soient conformes aux normes CE.
EN166 should be used. However all aspects of operators work, environment and other type/s of machinery being
used, should also be considered when selecting any personal protection equipment. Note: Non-side shielded
DE Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte Kopien dieses Dokuments erfüllen nicht
spectacles and face shields alone do not provide adequate protection.
die CE-Richtlinien für Produkte.
m WARNING! To prevent accidental injuries:
• Never place a hand or any other part of the body in fastener discharge area of tool.
NL Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige kopieën van dit document willen niet
• Never point tool at yourself or anyone whether it contains fasteners or not.
zeggen dat de producten voldoen aan de CE-vereisten.
• Never engage in horseplay.
• Never pull the trigger unless the nose is directed towards the work.
DK Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument udgør ikke CE overholdelse for
• Always handle the tool with care.
produkterne.
• Use the Bostitch tool only for the purpose for which it was designed, such as: the finishing around doors,
windows and edging; draw bottoms, cabinet backs and cabinet making; picture framing and furniture trim.
FI Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt kopiot eivät muodosta tuotteille CE-
These tools should not be used for anything other than wood to wood applications.
yhdenmukaisuutta.
• Do not pull the trigger or depress the work safety yoke whilst loading the tool.
• To prevent accidental actuation and possible injury, always disconnect air supply.
GR Απαγορεύεται η αναπαραγωγή χωρίς προηγούμενη άδεια. Τα μη εξουσιοδοτημένα αντίγραφα του παρόντος
1. Before making adjustments. 2. When servicing the tool. 3. When clearing a jam. 4. When tool is not in use.
εγγράφου δεν αποτελούν συμμόρφωση CE για τα προϊόντα.
5. When moving to a different work area, as accidental actuation may occur, possibly causing injury.
• Read the additional Safety & Operating instructions booklet before using tool.
IT Vietata la riproduzione senza permesso. Le copie non autorizzate di questo documento non garantiscono la
• Do not use oxygen and combustible gases as an energy source for pneumatically operated tools.
conformità CE per i relativi prodotti.
• The operation of this tool can cause sparks and act as a source of ignition for flammable fuels and gases.
NO Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette dokumentet oppfyller ikke kravene for CE-
LOADING
merking for produktet.
m Warning! When loading the tool 1) Never place a hand or any part of the body in fastener discharge area
of the tool; 2) Never point the tool at self or anyone else; 3) Do not pull the trigger or depress the safety yoke as
PT Reprodução proibida sem autorização prévia. As cópias não autorizadas deste documento não estão em
accidental actuation may occur, possibly causing injury.
conformidade com a CE para os produtos.
1. Depress magazine release button and pull back magazine. (Fig 1)
ES Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
BT1855, BT1855SP
2. With magazine fully open, insert fasteners. Points must be against bottom of magazine. (Fig 2)
FN1650, FN1650SP
conformidad con las normas CE de los productos.
(Figs 1-3)
3. Push magazine forward. Continue pushing until latch is engaged. (Fig 3)
SE Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
1. Depress magazine release button and pull back magazine. (Fig 4)
conformidad con las normas CE de los productos.
SX1838
2. Open magazine fully. Turn tool sideways with discharge area pointed away from yourself
SL540
& others. Load staples in channel. (Fig 5)
(Figs 4-6)
PL Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu nie
3. Push magazine forward. Continue pushing until latch is engaged. (Fig 6)
stanowią deklaracji zgodności CE prezentowanych produktów.
1. Load nails through the slot in the rear of the magazine and past retaining clip. (Fig 7)
FN1664
2. Pull pusher back behind nail stick and release. (Fig 8)
FN1664SP
CZ Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu nie
3. Ensure magazine pusher is behind the last nail stick. (Fig 9)
(Figs 7-9)
stanowią deklaracji zgodności CE prezentowanych produktów.
FASTENER LOCK OUT (BT1855, FN1664, SX1838)
SK Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto dokumentu nie sú v súlade s CE pre dané
výrobky.
These tools employ a mechanism to prevent dry firing of the tool. When the magazine is not loaded with nails or
when the remaining number of nails becomes less than ≈10, the contact arm cannot operate and the tool will not
HU A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül sokszorosított dokumentum nem jelenti
fire.
a termék CE-megfelelőségét.
RO Reproducerea neautorizată este interzisă. Copiile neautorizate ale acestui document nu reprezintă
conformitatea CE pentru produse.
GB