Parts And Accessories; Connecting The Oximeter; Attaching The Sensor; Starting Treatment - DeVilbiss Nonin XPOD Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 6
EN

PaRTs anD aCCessoRIes

The DV5M-697 Oximeter Kit contains the following items:
1.
9054D-693
Nonin XPOD Oximeter
2.
9054D-695
Nonin Sensor (8000J reusable FlexSensor)
ConneCTInG The oxIMeTeR (figure 1)
1.
Plug the oximeter into the bottom circular connector on the side of the DV5M SmartLink
Module.
2.
Connect the supplied sensor to the oximeter. Match the two arrows on each end of the
cables when inserting the oximeter to the sensor.
3.
When an oximeter is first connected and the sensor placed onto the finger, a visual
notification will be displayed after about ten (10) seconds to signal the presence of new
oximetry (SpO
) data. SpO
2
4.
Pulse Rate (PR) and oximetry (SpO
A display screen on the LCD display shows real-time SpO
the oximeter is not connected or if valid data is not available. This feature is to confirm that the oximeter is connected and working properly. If the
"***" persists, check connections and verify proper sensor placement and consult the sensor instructions for troubleshooting.
If the sensor is removed from the finger or the signal is lost for more than 10 seconds, the unit will begin to display a visual notification every 8
seconds until the oximeter is re-secured or sensor is replaced onto the finger or a timeout threshold of one minute is reached.
If the oximeter is unplugged from the SmartLink, no notification will occur and the unit will cease logging oximetry data.
The DV5M SmartLink is capable of storing 72 hours of oximetry data (9 days at 8 hours per day).

aTTaChInG The sensoR

For instructions on attaching the sensor, refer to the respective pulse oximeter sensor package insert.
NOTE
–The sensor will not function properly if there is nail polish on your fingernails.
NOTE
–Check that the sensor is not damaged. If damaged, contact your equipment supplier.
NOTE
–Do not attach the sensor to the oximeter until you are ready to start using the device.

sTaRTInG TReaTMenT

Start treatment as described in your IntelliPAP™ or SleepCube™ Instruction Guide. The SmartLink will automatically collect and store treatment
data.

PeRIoDIC InsPeCTIon

The XPOD oximeter and sensor should be inspected before and after each use. Inspect sensor wires and cables for breaks in the insulation or
visible damage. Replace any sensors or cables that have visible damage. Follow the cleaning instructions for the various components of the oximeter
system.
CleanInG The PUlse oxIMeTeR
Clean the XPOD oximeter separately from the sensor. For instructions on cleaning pulse oximeter sensor, refer to the respective pulse oximeter
sensor package insert(s).
CAUTION- To prevent product damage, do not submerse device in either water or any other fluid and do not use caustic or abrasive
cleaning agents.
Clean the oximeter components with a soft cloth dampened with isopropyl alcohol. Do not pour or spray any liquids onto the XPOD oximeter and
do not allow any liquid to enter any openings in the device. Allow the oximeter components to dry thoroughly before reusing.
4
A-M697
pArTs/ConneCTIng The oxIMeTer/ATTAChIng
sensor/TreATMenT/InspeCTIon/CleAnIng
will be displayed on the CPAP LCD.
2
) data is available on the SmartLink menus.
2
and Pulse Rate (updated once every second). Both values will be displayed as "***" if
2
1
Connecting the Oximeter to the DV5M SmartLink
Module.

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Dv5m-697

Tabla de contenido