Care & Maintenance; Burner Components - Pit Boss PLATINUM KC COMBO PB1285KC Manual De Instrucciones

Any Pit Boss® unit will give you many years of flavorful service with minimum cleaning. Follow these cleaning and maintenance tips to
service your grill:
CHECKING THE GAS LEVEL
To check the amount of fuel in the LP gas cylinder, the grill must be in operation. Place your hand at the top of the tank and slowly move
down the side until the tank feels cool to the touch. This will indicate the approximate amount of gas in your tank; if ¾ empty, replace
with full tank.
IMPORTANT: Do not use charcoal briquettes or any flammable material with your grill. Use of such material will
void your warranty and may lead to a fire, explosion and bodily harm.

1. BURNER COMPONENTS

• Clean the burner whenever heavy build-up is found, to ensure that there are no signs of blockage (debris, insects) on the
burner tube or in the burner portholes. After periods of storage, spiders or small insects can build nests, webs, and lay eggs
in the burner tube, obstructing the flow of gas to the burner. If storing the grill or before an extended period of non-use,
remove the burner and wrap with aluminum foil to reduce the risk of insects entering the burner holes.
• The burner has been preset for optimal flame performance. A blue flame, possibly with a small yellow tip, is the result of
the optimal air and gas mixture. If flames are excessively yellow, orange or irregular, clean the oil and food deposits on the
burner surface and the burner portholes to increase airflow.
2. HOPPER ASSEMBLY
• The hopper includes a clean-out feature to allow for ease of cleaning and
change out of pellet fuel flavors. To empty, locate the plate on the side of
the hopper and the cover of the drop chute on the back side of the hopper.
Place a clean, empty pail under the drop chute cover, then remove the cover
piece. Unscrew the plate, slide outwards, and pellets will empty.
NOTE: Use a long handled brush or shop-vac to remove excess pellets,
sawdust, and debris for a complete clean-out through the hopper screen.
• Running all pellets out of your auger system is recommended if your grill will be unused for an extended period of time. This
can be done by simply running your grill, on an empty hopper, until all pellets have emptied from the auger tube.
• Check and clean off any debris from the fan air intake vent, found on the bottom of the hopper. Once the hopper access
panel is removed (see Electric Wire Diagram for diagram), carefully wipe off any grease build-up directly on the fan blades.
This ensures airflow is sufficient to the feed system.
3. PROBES
• Kinks or folds in the probe wires may cause damage to the part. Wires should be rolled up in a large, loose coil.
• Although the probes are stainless steel, do not place in the dishwasher or submerge in water. Water damage to the internal
wires will cause the probe to short-out, causing false readings. If a probe is damaged, it should be replaced.
4. INSIDE SURFACES
• It is recommended to clean your fire pot after every few uses. This will ensure proper ignition and avoid any hard build-up
of debris or ash in the fire pot.
• Use a long-handled grill cleaning brush (brass or soft metal), remove any food or build-up from the cooking grids. Best
practice is to do this while they are still warm from a previous cook. Grease fires are caused by too much fallen debris on the
cooking components of the grill. Clean the inside of your grill on a consistent basis. In the event you experience a grease fire,
keep the grill lid closed to choke out the fire. If the fire does not go out quickly, carefully remove the food, turn the grill off,
and shut the lid until the fire is completely out. Lightly sprinkle baking soda, if available.
• Check your grease bucket often, and clean out as necessary. Keep in mind the type of cooking you do.
IMPORTANT: Due to high heat, do not cover the flame broiler or probes with aluminum foil.
CARE AND MAINTENANCE
COVER
PLATE
29