3M 5F-1 Manual De Usuario página 34

An
3M™ Clear Face shields
Please read these user instructions in conjunction with the appropriate 3M™ Carrier
system where you will find additional information on:
• Approved combinations of face shields
• Proper use and fitting of face shields
See all instructions for use and save for continuing reference.
INTENDED USE
3M™ Face shields when used as part of an approved system are designed to protect the
wearer against impacts to the eye and face, both from the front and the side.
3M™ Face shields mentioned in this user instruction are compatible for use with the 3M™
G500 Headgear or 3M™ V5 Linkage System.
3M™ Clear Face shields meet the requirements of EN166:2001, Personal Eye Protection.
^ Particular attention should be given to warning statements where indicated.
^ WARNINGS
Always be sure that the complete product is:
- Suitable for the application;
- Fitted correctly;
- Worn during all periods of exposure;
- Replaced when necessary.
Proper selection, training, use and appropriate maintenance are essential in order for
the product to help protect the wearer from impact hazards.
Failure to follow all instructions on the use of these personal protection products and/or
failure to properly wear the complete product during all periods of exposure may
adversely affect the wearer's health, lead to severe or life threatening illness or
permanent disability.
For suitability and proper use follow local regulations, refer to all information supplied or
contact an occupational hygienist, safety professional or 3M representative on the Tech
Assist Helpline 3M Australia 1800 024 464, 3M New Zealand 0800 364 357.
Check apparatus is complete, undamaged and correctly assembled. Any damaged or
defective parts must be replaced with original 3M spare parts before use.
Eye protectors against high speed particles worn over standard opthalmic spectacles
may transmit impact energy, creating a hazard to the wearer.
Certain chemicals can cause damage to these products.
Contact 3M for additional information.
If protection against high speed particles at extremes of temperature is required then
the selected eye-protector should be marked with the letter T immediately after the
impact letter, i.e. FT, BT or AT.
If the impact letter is not followed by the letter T then the eye protector shall only be
used against high speed particles at room temperature.
APPROVALS
These products meet the requirements of the European Community Directive 89/686/EEC
(Personal Protective Equipment Directive) and are thus CE marked.
Certification under Article 10, EC Type-Examination, has been issued for these products
by Finnish Institute of Occupational Health (FIOH), Topeliuksenkatu 41aA, FIN-00250
Helsinki, Finland (Notified Body number 0403).
CERTIFICATION
3M™ face shields meet the following requirements:
Model European Scale Optical Symbol Field of use
Standard Number Class
EN166:2001 2C-1.2 1 BT
5F-1,
5F-2
A
3
8
9
K
N
5E-1 EN166:2001 5 1 BT
3
9
K
N
Mechanical
Strength
High speed particles
Medium energy
at extremes of impact
temperature
High speed particles High energy
impact
Liquid splash
Short circuit electric
arc
Molten metal splash
Resistance to
surface damage by
fine particles
Resistance to
fogging
High speed particles High energy
at extremes of impact
temperature
Liquid splash
Molten metal splash
Resistance to
surface damage by
fine particles
Resistance to
fogging
33
^ If the face shield and the frame are not both marked with the same symbol, the
lowest level applies to the complete face protector.
PREPARATION FOR USE
Inspect the product carefully before each use. Replace any parts that show signs of
damage such as scratches or cracks.
FITTING INSTRUCTIONS
See Figure 1.
1. Fitting instructions for face shields
MARKING
See Figure 2. for face shield and frame markings.
1. Manufacturer
2. CE mark
3. European standard, field of use and symbol for class of impact protection
4. Type designation of face shield
5. Type designation of frame
NOTE: Other global markings (e.g. ANSI, CSA) may be present. For more information
contact 3M.
TECHNICAL SPECIFICATION
Face shield 5F-1
Polycarbonate
Minimum Thickness: 1.5mm
Weight: 138g
Coating: Outside - Anti-fog, Inside - Anti-fog
Face shield 5F-2
Polycarbonate
Minimum Thickness: 1.5mm
Weight: 138g
Coating: Outside - Hard-coat, Inside - Anti-fog
Face shield 5E-1
Polycarbonate
Minimum Thickness: 1.5mm
Weight: 140g
Shade: 5
Coating: Outside - Anti-fog, Inside - Anti-fog
CLEANING INSTRUCTIONS
The product should be cleaned regularly using a mild solution of detergent in warm water.
STORAGE AND TRANSPORTATION
Do not store the product in direct sunlight or at high temperatures.
When not in use, it should be stored in a cool, dark location to prevent the material from
ageing.
The recommended maximum shelf life of the product is 5 years from the date of
manufacture.
The original packaging is suitable for transporting the product.