Riester RCS-100 Instrucciones De Uso página 20

8.1 Steps for eardrum imaging:
1) Connect the inflation system (when a pneumatic test is
required).
2) Install disposable specula.
3) Tap to select the left or right ear
to be examined.
4) Tap L/M/H to select the specula,
low (L), medium (M), high (H)
5) The examiner pulls the auricle using one hand to
straighten the ear canal as much as possible, and using
the other hand gently put the lens into the external
auditory canal until the front end of OT reaches the
cartilage site.
6) Tap to enter adjust brightness
wheel or slide the process bar to adjust brightness of
the picture.
7) Tap to select manual/auto focus.
When is selected, click on the position in the pre-
view area where you want to focus, the system will
automatically focus according to the selected position.
When is selected , turn the wheel or drag the focus
progress bar on the touch screen to complete manual
focus.
8) Tap to select a capture mode.
To take photos
a) When photo mode is selected:
Tap to enter picture taking photo mode
• Tap again or turn the wheel to capture photo.
• When the photo has captured,
the image will be saved in Wifi-SD (if used) or to the inter-
nal storage, if "Save" is selected in the pop-up window. If
"Don't save" is selected, the image will be discarded.
To record video
b) When video mode is selected:
• Tap to enter video capture mode
• Tap or turn the wheel to start the video and
change to .
• Tap or turn the wheel to stop the video with showing
the saving reminder information. And the video will be
saved in Wifi-SD (if used) or in internal memory.
9) Tap to review the results of the photo or start the next
photo.
9 Imaging using optics module dermatoscope (DE)
The RCS-100 camera with dermatoscope lens is intended
to capture digital images and videos of the skin. The focus
position of the DE is preset at the factory, and in the "Der-
matoscope Focus Correction" in the Setting page, user can
reset the focus position (see the detail at section 8.6). The
dermatoscope has a ruler that can measure the length of the
part to be photographed. The picture brightness can be au-
tomatically adjusted by the system according to the illumina-
tion intensity of the subject in real time, and it can be adjus-
ted manually.The brightness level can be adjusted manually
from 0 to 6 (the default is 2). Illumination will turn off when
the brightness level is at the lowest level, and it will turn on
when the brightness level is more than the lowest level.
The device set for skin imaging consists of:
• Camera handset
• Attachable DE
function and turn
.
will change to , and
.
will
9.1 Steps for skin imaging:
1) Clean the lens and the part of the skin area to be
photographed.
2) Hold the handset and hold the lens against the skin area
of the patient to be tested.
3) Tap to enter adjust brightness
turn wheel or drag the process bar to adjust brightness
of the picture.
4) Click and drag one end of the ruler or hold the middle
of the ruler and move it in parallel to adjust the ruler to
the appropriate measurement angle and position.
5) Tap to select a capture mode.
To take photos
a) When photo mode is selected:
• Tap to enter picture taking photo mode
• Tap again or turn the wheel to capture photo.
• When the photo has captured,
the image will be saved in Wifi-SD (if used) or to the in-
ternal storage, if "Save" is selected in the pop-up window.
If "Don't save" is selected, the image will be discarded.
To record video
b) When video mode is selected:
• Tap to enter video capture mode
• Tap again or turn the wheel to start the video, and
will change to .
• Tap or turn the wheel to stop the video with showing
the saving reminder information. And the video will be
saved in Wifi-SD (if used) or in internal memory.
6) Tap to review the results of the photo or start the next
photo.
7) After the photo is taken, clean the part of the lens that
camera contact with the patient.
10 Imaging using optics module general lens (GE)
The RCS-100 camera with general lens has an object range
of 30 mm ~ 4 m, is intended to capture digital images and
video of mouth and throat.
The picture brightness can be automatically adjusted by the
system according to the illumination intensity of the subject
in real time, and it can be adjusted manually.
The brightness level can be adjusted manually from 0 to 6
(the default is 2). Illumination will turn off when the bright-
ness level is at the lowest level, and it will turn on when the
brightness level is more than the lowest level.
The device set for general imaging consists of:
• Camera handset
• Attachable GE
function and
.
will change to , and
.
20