Putting In Function And Stacker Utilisation; Preliminary Controls; Forward And Reverse Movement Operations; Lifting And Lowering Operations - Pegasolift W12 Guia Uso Y La Mantenimento

PUTTING IN FUNCTION AND STACKER UTILISATION

PUTTING IN FUNCTION AND STACKER UTILISATION

PRELIMINARY CONTROLS:

PRELIMINARY CONTROLS:
The stacker ready to use must be in the following conditions: The stacker ready to use must be in the following conditions:
1) Battery loading tap: disconnected. 1) Battery loading tap: disconnected.
2) Start switch: deactivated with the key taken out. 2) Start switch: deactivated with the key taken out.
3) Switch for disconnecting the battery: connected. 3) Switch for disconnecting the battery: connected.
4) Tiller bar: in vertical position 4) Tiller bar: in vertical position
5) Lifting group: completely lowered. 5) Lifting group: completely lowered.

FORWARD AND REVERSE MOVEMENT OPERATIONS:

FORWARD AND REVERSE MOVEMENT OPERATIONS:
FORWARD FORWARD
1 - BRAKING 1 - BRAKING
2 - RUNNING 2 - RUNNING
1 1
2 2
1 1

LIFTING AND LOWERING OPERATIONS

LIFTING AND LOWERING OPERATIONS
1) Introduce the forks in the lower part of the pallet on which the load is put with 1) Introduce the forks in the lower part of the pallet on which the load is put with
maximum of care and minimum speed; it is recommended for a bigger stability of maximum of care and minimum speed; it is recommended for a bigger stability of
the load to introduce completely the forks (see page 11 "Transport of load"). the load to introduce completely the forks (see page 11 "Transport of load").
2) Control that the load is equally distributed on the forks and the positions of the 2) Control that the load is equally distributed on the forks and the positions of the
barycenter is within the limits shown by the arrow on the stacker. barycenter is within the limits shown by the arrow on the stacker.
3) For lifting: keep pushing the button for lifting (reference page 14 "Tiller head" no. 6) 3) For lifting: keep pushing the button for lifting (reference page 14 "Tiller head" no. 6)
until the desired height is achieved. until the desired height is achieved.
4) For lowering: keep pushing the button for descent (reference page 14 "Tiller head" 4) For lowering: keep pushing the button for descent (reference page 14 "Tiller head"
no. 4) until the desired height is achieved. no. 4) until the desired height is achieved.
ATTENTION! ATTENTION!
executed only with the stacker completely stopped. executed only with the stacker completely stopped.
W12
BACK BACK
control buttons for movement: turning in the control buttons for movement: turning in the
Fig. B Fig. B
sense of watch needles the stacker moves sense of watch needles the stacker moves
forward, in the contrary sense the stacker forward, in the contrary sense the stacker
moves reverse. moves reverse.
Controlling in an adequate manner the Controlling in an adequate manner the
turning there it is easy to control the stacker turning there it is easy to control the stacker
speed. speed.
It is advised to avoid abrupt and repeated It is advised to avoid abrupt and repeated
starts and slowing down in order to avoid starts and slowing down in order to avoid
overheating of the motor and rapid overheating of the motor and rapid
discharge of the battery. discharge of the battery.
The load lifting and lowering operations should be The load lifting and lowering operations should be
15 15
1) Introduce the start key. 1) Introduce the start key.
2) Push simultaneously 2) Push simultaneously
with both hands the tiller with both hands the tiller
head and bring it in a quite head and bring it in a quite
horizontal position: the horizontal position: the
positions completely positions completely
horizontal and vertical horizontal and vertical
forbid the forward and forbid the forward and
reverse movement (figure reverse movement (figure
B). B).
3) Operate the butterfly 3) Operate the butterfly
UK15