Ryobi RPW2400 Manual De Utilización página 20

FR
EN DE ES IT
EN
FR DE ES IT
DE
FR EN ES IT
ES
FR EN DE IT
staRting and stOPPing tHe PRessuRe WasHeR
IT
FR EN DE ES
See Figures 11 - 12.
CautiOn:
FR EN DE ES IT
Do not start the pressure washer without the
FR EN water supply connected and turned on. DE ES IT
Before starting the engine:
FR EN DE ES IT
Check all hoses for damage.

 Connect all hoses.
FR EN DE ES IT
Check all fluids (lubricant and petrol).

Turn on the garden hose then squeeze the trigger
 FR EN DE ES IT
to relieve air pressure; hold the trigger until a steady
FR EN DE ES IT
stream of water appears.
Push ON/OFF switch to ON position.

FR EN DE ES IT
to start the engine:
FR EN DE ES IT
Push choke lever in to start position.

FR EN DE ES IT
Grasp the recoil starter and pull slowly until

resistance is felt. Give the recoil starter a short, brisk
FR EN DE ES IT
pull to start the engine.
nOte: Do not allow the recoil starter to snap back after
FR EN DE ES IT
starting; return it gently to its original place.
FR EN DE ES IT
Let engine run for several seconds, then pull choke

lever out to run position.
FR EN DE ES IT
to stop the engine:
FR EN DE ES IT
On the side of the engine is an "O" (Stop) switch. Press
FR EN DE ES IT
and hold the switch in the "O" (Stop) position for 3
seconds or until the engine stops.
FR EN DE ES IT
using tHe gun
FR EN DE ES IT
See Figure 13.
FR EN DE ES IT
For greater control and safety, keep both hands on the
gun at all times.
FR EN DE ES IT
Pull back and hold the trigger to operate the

pressure washer.
FR EN DE ES IT
 Release the trigger to stop the flow of water through
the nozzle.
to engage the lock out:
Pull back on the lock out until it clicks into the slot.

to disengage the lock out:
Push the lock out down and into its original position.

For the most effective cleaning, the spray nozzle should
be between 20cm and 60cm from the surface to be
cleaned. If the spray is too close it can damage the
cleaning surface.
seleCting tHe RigHt QuiCK COnneCt nOZZle
FOR tHe JOB
See Figure 14 - 15.
Before starting any cleaning job, determine the best
nozzle for the job. Each of the nozzles has a different
PT NL SV DA NO
PT NL SV DA NO
PT NL SV DA NO
PT NL SV DA NO
PT NL SV DA NO
PT
NL SV DA NO
NL
PT SV DA NO
SV
PT NL DA NO
DA
PT NL SV NO
NO
PT NL SV DA
PT NL SV DA NO
PT NL SV DA NO
PT NL SV DA NO
PT NL SV DA NO
PT NL SV DA NO
PT NL SV DA NO
PT NL SV DA NO
PT NL SV DA NO
PT NL SV DA NO
PT NL SV DA NO
PT NL SV DA NO
PT NL SV DA NO
PT NL SV DA NO
PT NL SV DA NO
PT NL SV DA NO
FI EL HU CS RU
FI EL HU CS RU
FI EL HU CS RU
english
FI EL HU CS RU
spray pattern. The supplied nozzles are: 40˚ White (for
FI EL HU CS RU
gentle cleaning), 25˚ Green (for general purpose cleaning
or large surfaces), 0˚ Red (for spot cleaning or high-to-
FI EL HU CS RU
reach areas), and Low Pressure Black (for detergent
FI EL HU CS RU
application and rinsing).
FI EL HU CS RU
WaRning:
NEVER change nozzles without engaging the
FI EL HU CS RU
lock out on the gun and NEVER point the lance at
FI EL HU CS RU your face or at others. The Quick Connect collar
contains small springs that could eject the nozzle
FI
EL HU CS RU
with some force. Failure to heed this may cause
personal injury.
EL
FI HU CS RU
Using the Quick Connect collar, changing nozzles is
HU
easy.
FI EL CS RU
CS
FI EL HU RU
to connect a nozzle to the lance:
Turn off the pressure washer and shut off the water

RU
FI EL HU CS
supply. Pull trigger to release water pressure.
Engage the lock out on the gun by pulling down on

FI EL HU CS RU
the lock out until it clicks into the slot.
Push the nozzle into the Quick Connect collar until it

FI EL HU CS RU RO
clicks in place and is secured properly.
FI EL HU CS RU RO
to disconnect a nozzle from the lance once the
FI EL HU CS RU RO
cleaning job is complete:
Turn off the pressure washer and shut off the water

FI EL HU CS RU RO
supply. Pull trigger to release water pressure.
Engage the lock out on the gun by pushing down on
FI EL HU CS  RU RO
the lock out until it clicks into the slot.
FI EL HU CS RU RO
Remove the

pulling back the Quick Connect collar. Place nozzle
FI EL HU CS RU RO
in the nozzle storage area on the top of the pressure
washer.
FI EL HU CS RU RO
FI EL HU CS RU RO
WasHing WitH deteRgent
See Figure 16.
Use only detergents designed for pressure washers;
house hold detergents, acids, alkalines, bleaches,
solvents, flam mable material, or industrial grade
solutions can damage the pump. Many detergents may
require mixing prior to use. Prepare cleaning solution as
instructed on the solution bottle.
Remove the cap from the detergent container. Place

the injection hose with filter in the bottle, the filter
end should rest at the bottom of the bottle.
Install the Low Pressure Black nozzle on the lance.

Spray the detergent on a dry surface using long,

even, overlapping strokes. To prevent streaking, do
not allow detergent to dry on the surface.
Before shutting off the engine:
Place

Flush for 1 - 2 minutes (spray clear water through

the lance).
Shut off the

17
RO PL SL HR TR
RO PL SL HR TR
RO PL SL HR TR
RO PL SL HR TR
RO PL SL HR TR
RO PL SL HR TR
RO PL SL HR TR
RO PL SL HR TR
RO PL SL HR TR
RO PL SL HR TR
RO PL SL HR TR
RO PL SL HR TR
RO PL SL HR TR
RO PL SL HR TR
RO PL SL HR TR
RO
PL SL HR TR
PL
SL HR TR
SL
PL HR TR
HR
PL SL TR
TR
PL SL HR
PL SL HR TR
PL SL HR TR
nozzle by placing hand over nozzle then
PL SL HR TR
PL SL HR TR
PL SL HR TR
the injection hose in a
engine.
ET LT LV SK BG
ET LT LV SK BG
ET LT LV SK BG
ET LT LV SK BG
ET LT LV SK BG
ET LT LV SK BG
ET LT LV SK BG
ET LT LV SK BG
ET LT LV SK BG
ET LT LV SK BG
ET LT LV SK BG
ET LT LV SK BG
ET LT LV SK BG
ET LT LV SK BG
ET LT LV SK BG
ET LT LV SK BG
ET LT LV SK BG
ET LT LV SK BG
ET LT LV SK BG
ET LT LV SK BG
ET
LT LV SK BG
LT
ET LV SK BG
LV
ET LT SK BG
SK
ET LT LV BG
BG
ET LT LV SK
bucket of clean water.