Denon DN-C680 Instrucciones De Operación página 24

20) Ò CD-R SkipON (OFF)Ó
CD-R SkipON : Play skip tracks on CD-R discs.
* CD-R SkipOFF : Do not play skip tracks on CD-R discs.
21) Ò 9600 (19200) bpsÓ
* 9600 bps : Set the baud rate to 9600 bps.
19200 bps : Set the baud rate to 19200 bps.
22) Ò Switch ENA (INH)Ó
* Switch ENA : Enable operation of all the switches on the front panel.
Switch INH : Inhibit operation of all panel switches other than those used for presetting operations.
23) Ò Player ID (**)Ó
Player ID (**) : Set the player ID.
24) Ò Remote EMA (INH)Ó
* Remote EMA : Enable input of control signals to the parallel remote connector.
Remote INH : Inhibit input of control signals to the parallel remote connector.
25) Ò St. Tally ON (OFF)Ó
* St. Tally ON : Output standby tally from parallel remote connector.
St. Tally OFF : Do not output standby tally from parallel remote connector.
26) Ò (******) TallyÓ
* INDEX2 Tally : Output index 2 tally signal to remote pin (17).
INDEX3 Tally : Output index 3 tally signal to remote pin (17).
27) Ò Fader Pause (Play)Ó
* Fader Pause : Start playback when remote fader pins (9-10) are short-circuited and pause when pins are open.
Fader Play : Start playback when remote fader pins (9-10) are short-circuited and continue playback when pins are open.
28) Ò Stereo (Mono)Ó
* Stereo : Output L and R stereo signals from the output connector.
Mono : Output mixed L and R signals from the output connector.
29) Ò Pos ON (OFF)Ó
Pos ON : Read Pos codes on CD and CD-R discs.
* Pos OFF : Do not read Pos codes on CD and CD-R discs.
30) Ò Preset CIr? (Init. Preset)Ó
Preset CIr? : Clear the presettings (set to the initial factory values).
* Init. Preset : Do not clear the presettings.
31) Ò Ver. xxxxÓ : Display the microprocessor version, (Ò xxxxÓ is a number.)
32) Ò Sync OFF(Word,Video)Ó (This setting can only be made when an optional synchronizing kit is mounted.)
* Sync OFF : Operation according to internal clock.
Sync Word : Synchronizing by word clock.
Sync Video : Synchronizing by video signal.
33) Ò 29.97fps DRF(29.97fps NDF,30fps,25fps)Ó (This setting can only be made when an optional synchronizing kit is mounted.)
* 29.97fps DRF : NTSC color,drop frame mode.
29.97fps NDF : NTSC color,non-drop frame mode.
30fps : NTSC black & White,non-drop frame mode.
25fps : PAL/SECAM
34) Ò LTC OFF(ON)Ó (This setting can only be made when an optional synchronizing kit is mounted.)
* LTC OFF : Synchronizing operation not performed.
LTC ON : Synchronizing operation performed.
35) Ò Type BVW75(PCM7050)Ó (This setting can only be made when an optional synchronizing kit is mounted.)
* BVW75 : Set the protocol type to BVW75.
PCM7050 : Set the protocol type to PCM7050.
36) Ò Chase(Auto Start)Ó (This setting can only be made when an optional synchronizing kit is mounted.)
* Chase : Playback locked to LTC time code.
Auto Start : Only start of playback performed when matched with set time code.
37) Ò Auto Memory(Manual Memory)Ó (This setting can only be made when an optional synchronizing kit is mounted.)
* Auto Memory : Set automatically when PLAY/PAUSE button pressed during LTC time code input.
Manual Memory : Set by inputting in units of hours,minutes,seconds and frames.
38) Ò 10h00m00s00fÓ (This setting can only be made when an optional synchronizing kit is mounted.)
* 10h00m00s00f : Display of hours(h),minutes(m),seconds(s) and frames(f).
(The ID can be set to OFF or to 0 to 15. The initial setting is Ò OFFÓ .)
ENGLISH
25