Part Names And Functions - Denon DN-C680 Instrucciones De Operación

1 PART NAMES AND FUNCTIONS

(1) Front Panel
q
POWER button
• This turns the set on and off.
w
Disc holder
• Place discs in this holder.
• Press the OPEN/CLOSE button to open and close the disc
holder.
• Load discs firmly inside the slot.
e
OPEN / CLOSE button
• Press this button to open and close the disc holder.
• The disc holder will not open during playback.
r
LEVEL control
• Use this to adjust the volume of the headphones.
t
PHONES jack
• Connect headphones with an impedance of 30 to 40
Ω/ ο η µ σ .
y
STOP button
• Press this button to turn all the servo functions off and stop.
• Press this button during playback to set the stop mode.
u
STANDBY/CUE button
• When this button is pressed during the play or pause mode,
the pickup returns to the position at which playback started
and the standby mode is set. (Back Cue)
• When pressed during playback when the next track has
been programmed, the programmed track is searched for
and the standby mode is set.
• The button lights when the standby mode is set.
• When the button is pressed while pressing the PLAY MODE
button, the preset mode is set.
i
PLAY/PAUSE button
• Press this button in the standby, pause or manual search
mode to begin playback.
• Press the button in the stop mode to search for the first
track and begin playback.
• The button lights during the play mode.
• When the button is pressed during playback, the pause
mode is set. The button flashes while the pause mode is
set.
o
PROG. PLAY ON/OFF button
• When this button is pressed while the PROGRAM IN button
is lit, the program play mode is set.
• The button will not function during the A-B play mode.
• The button lights during the program play standby and play
modes.
• When the button is pressed during the program play
standby or play mode, the program play mode is cleared.
!0
PROGRAM IN button
• Press this button to set the program input mode.
• The button will not function during the play mode.
• The button flashes when in the program input mode.
• The button lights when a program is set.
!1
Select knob
• Turn this knob to select the next track (or index number) to
be played.
• Use the INDEX button to choose whether to select tracks or
index numbers.
• Turn the knob clockwise by one click to move one track (or
one index number) forward, counterclockwise by one click
to move one track (or one index number) backward.
• When the knob turned while pressing it in, one click
corresponds to 10 tracks (or 10 index numbers).
• In the preset mode, use this knob to set and enter preset
settings.
• When setting programs, use this knob to select, enter and
check the program.
!2
PLAY MODE button
• Press this button to switch the play mode.
!3
PITCH button
• Press this button to switch to the play speed set with the +
and – buttons.
• The button lights when the pitch play mode is set.
• Press the button again to cancel the pitch play mode and
return to the normal speed.
!4
+ button
• Press this button once to increase the pitch by 0.1%.
• Hold the button in to increase the pitch continuously.
• Press the button in the program editing mode to set the
program insert mode.
!5
– button
• Press this button once to decrease the pitch by 0.1%.
• Hold the button in to decrease the pitch continuously.
• Press the button in the program editing mode to clear the
program.
!6
END MON button
• Press this button in the standby mode to monitor the end of
the track. (End Monitor)
• The button lights when the end monitor mode is set.
!7
REPEAT button
• Press this button to set the repeat mode.
• The button lights when the repeat mode is set.
• Press the button again to cancel the repeat mode.
!8
A button
• Press this button when no A point is set to set the A point.
• The button lights when the A point is set.
• When pressed while the A point is set, the A point is
searched for and the standby mode is set.
• When the button is pressed during manual search while the
A point is set, the A point changes.
!9
B button
• Press this button when no B point is set to set the B point.
• The button lights when the B point is set.
• When pressed while the B point is set, the B point is
searched for and the standby mode is set.
• When the button is pressed during manual search while the
B point is set, the B point changes.
ENGLISH
9