Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
6. Pull down on the shoulder protectors
place.
7. make sure the headrest fits the child's height, otherwise adjust the
headrest height as shown in fig. 5.5 and 5.6.
6. NIsTAllING THe cHIld seAT forWArd fAcING. GrouP 1
NoTIce
GROUP 1 only. From 9 months to 4 years approx. (9 - 18 kg)
1. Pull the lever
(G)
forward and adjust the angle of recline to position 1, 2,
or 3.
WARNING! once the car seat is installed, if you change the recline
position, you should repeat the car seat installation steps described below
to ensure a proper installation in this new position.
2 Place the seat in the back seat of the vehicle in the direction of travel.
3. Pass the vehicle seat belt through the slot on the side of the safety seat
(M)
until it appears at the exit, in the other side (fig. 6.2). Buckle the
vehicle seat belt until you hear a click (fig. 6.3).
4. Take up the slack by pulling the abdominal section of the belt until it is as
tight-fitting as possible.
5. Pass the diagonal part of the seat belt through the guide
of the seat as shown fig. 6.4 .
6. Take up the slack of the diagonal part of the car belt as much as possible
and ensure the straps are not twisted at any point (fig. 6.5).
7. cAr seAT INsTAllATIoN forWArd fAcING. GrouP 2/3
NoTIce
GROUP 2 /3. From 4 to 12 years approx. (15- 36 kg)
7.1 removing the buckle and the 5-point harness
1. Press the harness adjuster button
harness straps that cross the chest in order to loosen them ( fig. 5.1).
Do not pull the shoulder protectors.
32
(d)
to ensure they are properly in
(K)
at the top
(I)
while pulling the part of the
2. Loosen the harness straps from the back of the seat, freeing them from
the harness connector
(N)
(fig. 7.1).
3. Pull the harness straps from the front to free them from the seat back (fig.
7.2).
4. Turn the seat over and, from the back, take off the harness straps and
free the belt buckle
(e)
by passing the retention plate through the slot
in the seat (fig. 7.3).
5. Remove the belt buckle (fig. 7.4) and the harnesss straps and save them
in the storage bag.
7.2 Installing the child seat forward facing. Group 2/3
WARNING! in order to fasten the child to the safety seat, please use only
the 3 point vehicle's belt.
WARNING! make sure the 5-point harness and harness buckle have been
correctly removed.
1. Pull the lever
(G)
forward and adjust the angle of recline to position 1,
(fig. 7.5).
2. Place the seat in the seat in the direction of travel (fig. 7.6).
3. Place the child in the seat. Pull the vehicle safety belt and pass it in front
of the child until it reaches the vehicle seat belt buckle (fig. 7.7).
IMPORTANT! make sure the belt is not twisted.
4. insert the clasp into the vehicle seat buckle. You should hear a click (fig.
7.7).
5. make sure the abdominal belt pass by the lower guides
of the seat (fig. 6.7). Verify that the straps are taut and not twisted.
6. Pass the diagonal part of the car belt through the guide (P). make sure it
is fully extended and not twisted.
7. make sure the diagonal part of the belt passes over the child's collar bone
and not the neck.
IMPorTANT! The part of the abdominal belt should rest as low as possible
over the child's hips, on both sides.
(G)
on both sides
33
Publicidad
Tabla de contenido
