Adjusting The Harness Height - Babyauto TAIYANG 0123 Manual De Uso

3.1. Adjusting the harness height

in order to fit the harness to the child's height:
1. Loosen the harness straps by pulling them gently while pressing the
harness adjustment button
2. Loosen the harness straps from the back of the seat, freeing them from
the harness connector (N)
3. Pull the harness straps from the front to free them from the seat back.
4. Reinsert the harness straps in the slot
5. Reinsert the harness straps in the connector on the back of the seat.
6. Ensure the straps are not twisted at any point.
3.2. Installing the child seat rearward facing. Group 0+
1. Recline the seat fully. Pull the lever
recline to position 4 without releasing the lever. Release the lever when
the seat is in the desired position (fig. 3.4 and 3.5).
2. Turn the seat over and unfold the group 0+ height adjuster device
(fig.3.6).
3. Place the seat in the back seat of the vehicle in opposite direction of
travel.
4. Pass the abdominal strap of the car belt through the lower seat guides
(f)
(fig.3.7 and 3.8) and underneath the seat. Buckle the vehicle seat
belt until you hear a click (fig. 3.9).
5. Pass the diagonal section of the seat belt through the upper guide
as shown in fig. 3.9.
6. Take up the remaining slack of the diagonal section of the 3-point seat belt
and make sure it is as tight fitting as possible. Ensure the straps are not
twisted or knotted at any point (fig. 3.10).
4. INsTAllING THe cHIld seAT reArWArd fAcING. GrouP 1
GROUP 1 only. From 9 months to 4 years
NoTIce
approx. (9 - 18 kg)
A correctly adjusted headrest ensures optimal protection for the child in the
safety seat. The headrest should be adjusted so that the shoulder straps are at
the same height as the child's shoulders (fig. 3.1).
30
(I) (fig. 4.1).
(fig. 3.2 and 3.3).
(l) at the desired height.
(G) forward and adjust the angle of
1. Recline the seat fully. Pull the lever
recline to position 4 without releasing the lever. Release the lever when
the seat is in the desired position (fig. 3.4 and 3.5).
2. Turn the seat over and unfold the group 0+ height adjuster decive
(fig.3.6).
3. Place the seat in the back seat of the vehicle in opposite direction of
travel.
4. Take out the reducer cushion . Pass the abdominal strap of the seat belt
through the lower seat guides
vehicle seat belt until you hear a click (fig. 4.1).
5. Pass the diagonal section of the seat belt through the upper guide
as shown in fig. 4.1.
6. Take up the remaining slack of the diagonal section of the 3-point seat belt
and make sure it is as tight fitting as possible (fig. 4.2). Ensure the straps
are not twisted or knotted at any point (fig. 4.3).
7. Place the reducer cushion in his original place.
(Q)
5. PlAcING THe cHIld IN THe seAT . GrouP 0+/ 1.
NoTIce
1. Press the harness adjuster button
(K)
harness straps that cross the chest in order to loosen them ( fig. 5.1).
Do not pull the shoulder protectors.
2. Release the buckle by pressing the button
the child.
3. Place the child in the safety seat.
4. Secure the child in the harness by joining the two parts of the clasp /fig.
5.2/A) and fastening the buckle
5. Pull the harness adjustment strap
correctly to the child's body (fig. 5.4).
IMPORTANT! The part of the harness straps that crosses the abdomen should
be placed as low as possible on the child's hip.
(G) forward and adjust the angle of
(o) and underneath the seat. Buckle the
GROUP 0+/1. From 0 to 4 years approx. (0 - 18 kg)
(I) while pulling the part of the
(e) to make it easier to seat
(d) 5.2/B) until you hear a click (fig. 5.3).
(H) in order to tighten and adjust it
(Q)
(K)
31