Symbols Used In The Manual; Transport And Storage - salmson MULTI-V Serie Instalacion Y Puesta En Servicio

ENGLISH
1. GENERAL
1.1 Applications
Pumps for clear liquids in residential, agricultural, industrial, and other
applications. (water supply, water tower, sprinkling, irrigation, high
pressure washing, fire protection, lifting condensates, air conditioning,
industrial circuits and integration in all modular systems).
- Boiler water supply with mandatory BY-PASS kit.
1.2 Specifications
• Max. service pressure:
- PN 25 casing
- PN 25 casing
- PN 16 casing
- PN 25 - Fast joint pipe
for type collars "VICTAULIC"
• Max. suction pressure
• Temperature range:
- Version EPDM o'rings and mechanical seal: - 15° to + 120°C
(potable water WRAS/KTW approved version)*
- Version Viton o'rings and mechanical seal : - 15° to + 90°C
• Ambient temperature (standard)
• Suction head
* WRAS: to English standard. KTW: to German standard.
Sound level : Depend on pump size, rotation speed, working point,
motor type : it can reach 73 dB(A) in 50 Hz and 77 db(A) in 60 Hz.
2. SAFETY
Read this data sheet carefully before installing and starting up. Pay
special attention to the points concerning the safety of the equip-
ment for the intermediate or end user.

2.1 Symbols used in the manual

Security instruction : non respect can induce injury.
Electrical security instruction : non respect can induce injury.
Security instruction : non respect can be induce
CAUTION !
material damages.

3. TRANSPORT AND STORAGE

When taking delivery of the equipment, check that it has not been
damaged in transit. If anything is found wrong, take the necessary
steps with the carrier within the allowed time.
If the equipment delivered is to be installed at a
CAUTION !
later time, store it in a dry place and protect it from
impacts and outside hazards (moisture, frost, etc.).
Due to high position of centre of gravity and small ground sur-
face of this type of pumps, beware of unstability during hand-
ling to avoid any falling down and take necessary means to
avoid injuries or damaging.
Handle the pump carefully so as not to alter the geometry or align-
ment of the hydraulic assembly.
4. PRODUCTS AND ACCESSORIES
4.1 Description (see FIG. 1, 2 & 5)
1 : Foot valve-strainer
2 : Pump suction valve
3 : Pump discharge valve
4 : Check valve
5 : Air bleed-filling plug
6 : Drain-priming plug
7 : Pipe support or collars
8 : Strainer
9 : Storage tank
: 16 bars (50 & 60 Hz-4 poles)
: 25 bars (50 & 60 Hz-2 poles)
: 16 bars (50 & 60 Hz-2 poles)
: 16 bars (50 & 60 Hz-4 poles)
25 bars (50 & 60 Hz-2 poles)
: 10 bars
: + 40°C maxi
: depends on NPSH of pump
10 : Town water supply
11 : Motor protection relay
12 : Lifting hook
13 : Foundation block
14 : Cock
HA : Max. suction head
HC : Min. discharge head
4.2 The pump
Multistage vertical pump (2 to 24 stages), not self-priming, ports in line
at bottom.
Shaft sealing by standardized mechanical seal.
• Dimensions (See FIG. 3)
TYPE
Poles
MULTI-V-50Hz
102 116 2
102 124 2
202 212 2
202 220 2
402 412 2
402 419 2
410 420 4
102 420 2 and 4
802 812 2
802 819 2
810 819 4
1602 1611 2
1602 1611 2
1606 1612 4
802 1612 2 and 4
MULTI-V-60Hz
102 110 2
102 116 2
202 208 2
202 214 2
402 408 2
402 414 2
410 420 4
102 414 2 and 4
802 808 2
802 811 2
810 819 4
1602 1606 2
1602 1606 2
1605 1612 4
802 1612 2 and 4
• Flanges:
- Oval for PN 16 casing: pump supplied with cast-iron oval counter-
flanges for screw-in tube, with gaskets and bolts.
- Round for PN 25 casing: pump supplied with gaskets and bolts,
without counter-flanges (accessories in option).
- A fast joint pipe for collars type "VICTAULIC" : pump supplied with
no collars (accessories in option).
4.3 The motor
Sealed motor with standardized flange and shaft end for vertical
operation.
Motor and pump linked by a coupling with safety guards.
10
L P X
Casing mm mm mm
PN16
212 157 180
PN25
212 172 180
PN16
212 157 180
PN25
212 172 180
PN16
212 157 180
PN25
212 172 180
PN25
212 172 180
Victaulic 212
157 180
PN16
252 187 215
PN25
252 187 215
PN25
252 187 215
PN16
252 187 215
PN25
252 187 215
PN25
252 187 215
Victaulic 252
187 215
PN16
212 157 180
PN25
212 172 180
PN16
212 157 180
PN25
212 172 180
PN16
212 157 180
PN25
212 172 180
PN25
212 172 180
Victaulic 212
157 180
PN16
252 187 215
PN25
252 187 215
PN25
252 187 215
PN16
252 187 215
PN25
252 187 215
PN25
252 187 215
Victaulic 252
187 215
Y
mm
100
100
100
100
100
100
100
100
130
130
130
130
130
130
130
100
100
100
100
100
100
100
100
130
130
130
130
130
130
130