Radiator Hose Inspection; If Coolant Leaks; Checking Fan Belt Tension - Yamaha EDL13000SDE Manuel Del Propietario

MAINTENANCE
30
Engine oil capacity
Model
EDL13000STE
KJ-T130DX, KJ-T160DX
zEngine model : D1703x
EDL13000SDE, EDL15000SDE,
KJ-S130VX, KJ-S150VX,
EDL18000STE
KJ-T180VX, KJ-T210VX
zEngine model : V2203x
EDL30000STE
KJ-S240, KJ-T300
zEngine model : V3300x
IMPORTANT:
¡ Engine oil should be MIL-L-2104C or have
properties of API classification CD grades or
higher.
Change the type of engine oil according to the
ambient temperature.
above 25ºC (77ºF)
0 to 25ºC (32 to 77ºF)
below 0ºC (32ºF)
¡ When using oil of different brands from the
previous one, be sure to drain all the previous oil
before adding the new engine oil.
a Radiator Hose Inspection
1. Check to see if radiator hoses are properly fixed
every 250 hours of operation or six months,
whichever comes first.
¡ If clamp bands are loose or water leaks, tighten
bands securely.
¡ Replace hoses and tighten clamp bands
securely, if radiator hoses are swollen,
hardened or cracked.
2. Replace hoses and clamp bands every 2 years or
earlier if checked and found that hoses are
swollen, hardened or cracked.

If Coolant Leaks

a If coolant leaks
If steam or water comes out of the overflow line, stop
the engine immediately, and carry out the following
inspection and maintenance procedure.
3
WARNING
CAUTION:
¡ Stop the engine and wait until it
becomes cool to touch. Then
r e m o v e t h e r a d i a t o r c a p
carefully.
1. Check for the leakage and coolant levels.
2. Check the cooling air inlet and outlet for
obstructions.
3. Check the radiator fins for clogging. When
cleaning the radiator, never use a scraper. Blow
air through, or clean with a water spray.
4. Check the radiator water tubes for corrosion.
L
Capacity
5.6
7.6
13.2
SAE10W-30
SAE30 or
SAE10W-40
SAE10W-30
SAE20 or
SAE10W-40
SAE10W-30
SAE10W or
SAE10W-40
a Checking Fan Belt Tension
3
WARNING
CAUTION
To avoid personal injury:
¡ Be sure to stop the engine and
remove the key before checking
the belt tension.
¡ Be sure to reinstall the detached
safety shield after maintenance
or checking.
z z z z z Engine model : D1703-EBG, V2203-EBGx x x x x
z z z z z Engine model : V3300-EBGx x x x x
1. Stop the engine and remove the key.
2. Apply moderate thumb pressure to belt between
pulleys.
3. If tension is incorrect, loosen the alternator
mounting bolts and, using a lever placed between
the alternator and the engine block, pull the
alternator out until the deflection of the belt falls
within acceptable limits.
4. Replace fan belt if it is damaged.
IMPORTANT:
¡ If belt is loosen or damaged and the fan is damaged,
it could result in overheating or insufficient
charging. Adjust correctly or replace the belt.
z z z z z D1703-EBG, V2203-EBGx x x x x
(1) Fan belt
(2)Bolt and nut (A) 7 to 9 mm (under load of 98 N)
z z z z z V3300-EBGx x x x x
(A) 10 to 12 mm (under load of 64 N)