Starting Operation; After-Sales Service And Customer Assistance - stayer MULTI L20 Manual De Instrucciones

gb
If required, assemble the parts of the dust extraction
11 as shown in the figure. Position the assembled dust
extraction onto the machine via the tool holder 4.
Depending on machine version, place a vacuum hose
(accessory) either directly onto the vacuum connection
12. Connect the vacuum hose with a vacuum cleaner
(accessory). An overview for the connection of various
vacuum cleaners can be found on the fold-out page.
The vacuum cleaner must be suitable for the material
being worked.
When vacuuming dry dust that is especially detrimental
to health or carcinogenic, use a special vacuum cleaner.
4. OPERATION
Observe correct mains voltage! The voltage of the
power source must agree with the voltage specified
on the nameplate of the machine. Power tools
marked with 230 V can also be operated with 220 V.

STARTING OPERATION

Switching On and Off
To start the machine, push the On/Off switch 1 forward
so that the "I" is indicated on the switch.
To switch off the machine, push the On/Off switch 1
toward the rear so that the "0" is indicated on the switch.
Preselection of the number of oscillations
With the adjusting wheel 2, the number of oscillations
can be preselected, even with the appliance running.
The required number of oscillations depends on the
material and working conditions and it is therefore
recommended to determine it by testing.
Preselecting the Orbital Stroke Rate
Note: Do not cover off the venting slots 3 of the machine
while working, as this reduces the working life of the
machine.
Operating Principle
Due to the oscillating drive the application
tool/accessory swings up to 21000 times
per minute for 2.8°. This allows for precise
work in narrow spaces.
Work with low and uniform application
pressure, otherwise, the working
performance will decline and the
application tool can become blocked.
While working, move the machine back
and forth, so that the application tool does
not heat up excessively and become
blocked.
Sawing
- Use undamaged faultless saw blades only.
Deformed, blunt saw blades or saw blades that are
otherwise damaged can break.
- When sawing light building materials, observe the
statutory provisions and the recommendations of
the material suppliers.
- Plunge cuts may only be applied to soft materials,
such as wood, gypsum plaster boards, etc.!
Before sawing with HSS saw blades in wood, particle
board, building materials, etc., check these for foreign
objects such as nails, screws, or similar. If required,
remove foreign objects or use BIM saw blades.
Sanding
The removal rate and the sanding pattern are primarily
determined by the choice of sanding sheet, the preset
oscillation rate and the applied pressure.
Only flawless sanding sheets achieve good sanding
capacity and extend the service life of the machine.
Pay attention to apply uniform sanding pressure; this
increases the working life of the sanding sheets.
Intensifiying the sanding pressure does not lead to an
increase of the sanding capacity, but to increased wear
of the machine and the sanding sheet.
For precise on-the-spot sanding of edges, corners and
hard to reach areas, it is also possible to work only with
the tip or an edge of the sanding plate.
When selectively sanding on the spot, the sanding sheet
can heat up considerably. Reduce the orbital stroke rate
and allow the sanding sheet to cool down regularly.
A sanding sheet that has been used for metal should not
be used for other materials.
For sanding, always connect dust extraction.
Scraping
For scraping, select a high oscillation rate. Work on a soft
surface (e.g. wood) at a flat ange, and apply only light
pressure. Otherwise the scraper can cut into the surface.
5. MAINTENANCE AND SERVICE
MAINTENANCE AND CLEANING
- Before any work on the machine itself, pull the
mains plug.
- l For safe and proper working, always keep the
machine and ventilation slots clean.
Clean Riff application tools (accessory) regularly with a
wire brush. If the machine should fail despite the care
taken in manufacturing and testing procedures, repair
should be carried out by an after-sales service centre for
Stayer.

AFTER-SALES SERVICE AND CUSTOMER ASSISTANCE

Our after-sales service responds to your questions
concerning maintenance and repair of your product as
well as spare parts. Exploded views and information on
spare parts can also be found under:
info@grupostayer.com
Our customer consultants answer your questions
concerning best buy, application and adjustment of
products and accessories.
- 22 -