Operation; Switching On And Off; Controlling Chain And Guide Bar Lubrication; Cut Indicator - Festool SSU 200 EB Manual De Instrucciones Original

upwards and releases; when rotated counter
clockwise as seen from above, the pin moves
downward) so that the opening on the guide
bar [2-5] snaps into the tension bolt [2-6].
 Then put the chain sprocket cover [2-1] on the
clamping bolt [2-7] and tighten by rotating the
fastening wheel [2-2] clockwise.
 Before tightening it fi rmly, tension the chain
correctly, as described in Section 11.1.
8.2 Filling the oil reservoir
When the SSU 200 EB is delivered, the lubrication
oil reservoir is empty. Before using the machine,
you must fi ll the tank with chain oil to prevent
damage to the oil feed pump. If the machine is
operated with an insuffi ciently fi lled oil reservoir
or with a dysfunctional lubricating system, the oil
feed pump will be damaged, as well as the tool's
entire cutting assembly!
The oil reservoir cap [1-9] has an opening with a
one-way suction valve for air pressure compensa-
tion. If you use the machine in other than the verti-
cal position, the chain may not get lubricated. The
outlet of the oil reservoir is located down at the
back, and when the machine rotates, the pump
is not able to suck up the oil. The quantity of oil
in the reservoir is indicated by the level in the oil
gauge [1-8].
8.3 Electrical connection
WARNING
If the tool is used with an incorrect power supply,
there is a risk of injury.
The SSU 200 EB sword saw can only be connected
to a single-phase power supply with 220-240V/50–
60Hz alternating current. The machine has a class
II protective covering according to EN 60745-1 and
has noise suppression according to EN 55 014.
Before operating the machine, make sure that the
voltage of the socket corresponds to the voltage
information stated on the label of the machine.
The portable cord can be extended in the following
manner, if necessary:
- Length 20 m, cross-section of wires 3 × 1.5 mm
- Length 50 m, cross-section of wires 3 × 2.5 mm
Use only appropriately marked extension cords
intended for use outdoors.
28
9

Operation

WARNING
Risk of accident, electric shock
 Always pull the plug out of the socket before
performing any type of work on the machine.
9.1

Switching on and off

Before switching the machine on, tighten all
clamping and fi xing bolts. Handle the machine
with both hands, and put it on the cutting piece
so that the chain is loose and will not stick inside
the cut after activation.
To turn on
Press down on the safety lock [1-1] on the side
of the handle [1-2] and then actuate the motor
switch [1-2].
To turn off
Let up on the motor switch button [1-2]. The
safety lock [1-1] returns to its initial position,
which consequently prevents the unit from being
switched on unintentionally. When the machine is
turned off, an electric brake activates and signifi -
cantly shortens the run-down time of the chain.
Do not remove the machine from the cutting piece
until the chain is at a standstill.
9.2 Controlling chain and guide bar lubrica-
tion
The quantity of lubricating oil can be controlled
using a feed pump [5-2]. When you press the feed
pump, [5-2] the 0, 1, 2 and MAX positions can be
set at a notch [5-1]. Position 0 ensures minimum
lubrication for clean cuts, but must not be used
permanently, and after such cuts the chain and
plate must be lubricated with an increased quan-
tity. For permanent operation the quantity should
be set to level 2 and MAX.
9.3

Cut indicator

When cutting without the guide rail, adjust the
chain's internal cutting plane using all of the in-
dicators on the guide runner:
- Indicator 0° [4-1] for rectangular cuts
2 - For bevel cuts:
• indicator 45° [4-4]
2
• indicator 60° [4-5]
To determine the chain's external cutting plane,
use cutting profi le indicators [4-6].
For cutting with the guide rail adjust the chain's
inner cutting plane using only cut indicator 0° [4-
1].