Roland SP-808 Manual Del Usuario página 173

Byte Description
F0H Status of System Exclusive Message
7FH Universal System Exclusive Message Realtime Header
Dev Device ID (10H or 7FH)
06H MMC Command Message
4CH MOVE
02H Number of Bytes
ddH Name of the Efficient Destination Information Field
(08H,09H,0AH,0BH,0CH,0DH,0EH,0FH)
ssH Name of the Efficient Source Information Field (01H)
F7H EOX (End of System Exclusive Message)
If the device ID on the message was as same as that of the receiving 10H or 7FH, the SP-808
transfers the data on the selected source information field to the destination Information
Field, if the name of both information fields is efficient.
3. TRANSMITTED DATA
Channel Voice Message
Note On/Off
When "Metro." in the SYSTEM parameters(1.Set System Param?) is "MIDI", MIDI note
number/velocity of MIDI channel number which is assigned to the Metronome is
transmitted.
Status Second Third
9nH mmH llH
n = MIDI Channel No.: 00H–0FH (ch.1–ch.16) (*1)
mm = Note No.: 00H–7FH (0–127)
ll = Velocity: 01H–7FH (1–127) / 00H = NOTE OFF
*1 Only when transmitting Metronome.
Control Change
Parameters on the Mixer section can be received and transmitted by the control change
messages when "MIDI Mixer Control Type (*1)" in the SYSTEM parameter is set to "C.C."
Status Second Third
BnH mmH llH
n = MIDI Channel No.: 0AH–0FH (ch.11–ch.16:
mm = Mixer Parameter No.: (see below)
ll = Mixer Parameter Value: 00H–7FH (0–127)
Mixer Parameter and MIDI Channel/Control Change No.
<Mixer Channel Strip>
+—————————————————— Master
| +——————————————— Track A
| | +———————————— Track B
| | | +————————— Track C
| | | | +—————— Track D
| | | | |
| | | | |
MIDI ch. 11 12 13 14 15 16
Level 7 -> -> -> -> ->
Balance 10 -> -> -> -> ->
Effects Send Level 91 -> -> -> -> ->
AUX Send Level 92 -> -> -> -> ->
<Master Block> MIDI ch. = 11
Level 7
Balance 10
D Beam Controller L 80
D Beam Controller R 81
Effects Send Level 91
AUX Send Level 92
System Common Messages
MIDI Time Code Quarter Frame Messages
MIDI Time Code Quarter Frame Messages can be transmitted while the SP-808 is running
(Playing or Recording) if the SONG parameter "Sync Src" is "INTERNAL" and "Sync Out"
is "MTC". The transmitted time counts are summed to "MTC Offset Time" as the song top is
"00:00:00:00".
Status Second
F1H mmH (= 0nnndddd)
see below)
+——— MIC/LINE
|
nnn = Message type: 0 = Frame count LS nibble
1 = Frame count MS nibble
2 = Seconds count LS nibble
3 = Seconds count MS nibble
4 = Minutes count LS nibble
5 = Minutes count MS nibble
6 = Hours count LS nibble
7 = Hours count MS nibble
dddd = 4 bit nibble data: 0H–FH (0–15)
If the upper and lower 4 bits of the count are combined, these bit fields are assigned as
follows.
Frame Count xxxyyyyy
xxx Reserved (000)
yyyyy Frame No. (0–29)
Seconds Count xxyyyyyy
xx Reserved (00)
yyyyyy Seconds Count (0–59)
Minutes Count xxyyyyyy
xx Reserved (00)
yyyyyy Minutes Count (0–59)
Hours Count xyyzzzzz
x Reserved (0)
yy Time Code type
0 = 24 Frames/Sec
1 = 25 Frames/Sec
2 = 30 Frames/Sec (Drop Frame)
3 = 30 Frames/Sec (Non Drop Frame
zzzzz Hours
Song Position Pointer
The current position is transmitted with the Song Position Pointer Message before the SP-
808 starts to run or after the locate operation, when "Sync Src" is "INTERNAL" and "Sync
Out" is "MIDI CLOCK".
Status Second Third
F2H mmH nnH
mm,nn = Song Position Point: 00H 00H–7FH 7FH
System Realtime Message
Transmitted when "Sync Src" is "INTERNAL" and "Sync Out" is "MIDI CLOCK".
Timing Clock
Status
F8H
Start
Status
FAH
Continue
Status
FBH
Stop
Status
FCH
System Exclusive Message
Status Data Bytes Status
F0H iiH, ddH, ..., eeH F7H
Byte Description
F0H Status of System Exclusive Message
iiH Manufacturer ID
41H Roland's Manufacturer ID
7EH Universal Non Realtime Message
7FH Universal Realtime Message
ddH Data: 00H–7FH (0–127)
| |
eeH Data
F7H EOX (End of System Exclusive Message)
1
Apéndices
2
3
4
5
6
7
8
9
10
11
12
13
14
15
173