Dust Extraction; Optional Accessories; Protecting The Environment - Stanley SST1800 Traducción De Las Instrucciones Originales

ENGLISh
clean your power tool. Wipe clean with a dry cloth. Always store
your power tool in a dry place. Keep the motor ventilation slots
clean. Keep all working controls free of dust. If you see some
sparks flashing in the ventilation slots, this is normal and will not
damage your power tool. If the supply cord is damaged, it must
be replaced by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.

Dust Extraction

Dust from materials such as lead‑containing coatings and some
wood types, can be harmful to one's health. Breathing‑in the
dust can cause allergic reactions and/or lead to respiratory
infections of the user or bystanders. Certain dust, such as oak or
beech dust, is considered carcinogenic, especially in connection
with woodtreatment additives.
Observe the relevant regulations in your country for the
materials to be worked.
The vacuum cleaner must be suitable for the material being
worked.
When vacuuming dry dust that is especially detrimental to
health or carcinogenic, use dust class M vacuum cleaner.
The machine is provided with a dust collection port at the rear
of the machine suitable for use with dust extraction equipment
featuring 35 mm nozzles. The blade guard assembly also
features a dust collection port for 35 mm nozzles.
• During all operations, connect a dust extraction device
designed in accordance with the relevant regulations
regarding dust emission.
• Ensure that the dust extraction hose in use is suitable for
the application and material being cut. Ensure proper
hose management.
• A splitter accessory is available to connect both ports to a
single dust extractor.
• Be aware that man‑made materials such as chipboard
or MDF produce more dust particles during cutting than
natural timber.
C
Lubrication
Your power tool requires no additional lubrication.
Cleaning (Fig. A)

WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.

WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.

WARNING: To reduce the risk of injury, regularly clean the
table top and ventilation slots.
38

WARNING: To reduce the risk of injury, regularly clean the
dust collection system.

WARNING: To reduce the risk of serious personal injury, do
not use the saw without reattaching the dust access door.
The blade guard 2 and throat plate must be placed in position
before operating the saw.
Before use, carefully inspect upper and lower blade guards as
well as the dust extraction tube to determine that it will operate
properly. Ensure that chips, dust or work piece particles cannot
lead to blockage of one of the functions.
In case workpiece fragments are jammed between saw blade
and guards, disconnect the machine from the power supply
and follow the instructions given in Saw blade Assembly/
Replacement. Remove the jammed parts and reassemble the
saw blade.
Keep the ventilation slots clear and regularly clean the housing
with a soft cloth.
Regularly clean the dust collection system.

Optional Accessories


WARNING: Since accessories, other than those offered
by STANLEY , have not been tested with this product, use
of such accessories with this tool could be hazardous. To
reduce the risk of injury, only STANLEY recommended
accessories should be used with this product.
Consult your dealer for further information on the
appropriate accessories.
Replace the blade guard or carbon brush when worn. Contact
your local Stanley service centre for details on a blade guard or
carbon brush replacement.

Protecting the Environment

Separate collection. Products marked with this symbol
w
must not be disposed of with normal household waste.
Products contain materials that can be recovered
or recycled reducing the demand for raw materials.
Please recycle electrical products according to local provisions.
Further information is available at www.2helpU.com.