Basic Safety Instructions - Orbitalum RPG 3.0 Traducción Del Manual De Instrucciones Original

RPG 3.0, RPG 4.5 (S), RPG 8.6
2.4

Basic safety instructions

The maschine (hereinafter referred to as the RPG 3.0, RPG 4.5 (S) or RPG 8.6) is a state-of-the-art machine designed for safe use.
The risks involved in using the machine are described in the operating instructions below. Using this machine in a way other than
that described in these instructions can lead to serious physical injury and material damage.
Therefore:
• Observe warning messages at all times.
• In addition to this operating instructions, the general warning messages for electric tools (see supplement), which should
always be retained.
• Keep complete documentation close by the machine.
• Generally valid regulations for the prevention of accidents must be observed.
• Observe country-specific regulations, standards and guidelines.
• Use the machine only in perfect technical condition, otherwise have it repaired at a service point.
Observe the maintenance information (chap. 10, p. 68).
• The machine may only be operated if all safety equipment such as restarting block and overload protection is in proper
working order and the viewing window is closed. The machine must have a solid footing. Check whether the substrate is able
to take sufficient loads. A radial space requirement/freedom of movement of approx. 1 m around the machine is required for
people.
• Report any unusual machine behavior to the person responsible immediately.
• Only use the dimensions and materials specified in these instructions. Other materials should be used only after consulting
with Orbitalum Tools customer service.
• Use only original tools, spare parts, materials and accessories from Orbitalum Tools.
• Repair and maintenance work on the electrical equipment may only be carried out by a qualified electrician.
• At the end of each working cycle, before transportation, changing tools, cleaning and performing any maintenance, adjust-
ment or repair work, switch off the machine, wait until the machine/tool stops running and pull the mains plug or remove the
battery.
• Do not carry the machine by the cable and do not use the machine to pull out the mains plug except in an emergency. Protect
the cable from heat, oil and sharp edges (chips).
• During operation, keep hands away from the tools.
• Check that the tube is correctly clamped.
• Switch on the machine only when the tube has been clamped.
• Do not use the machine in wet surroundings. Only work in canopied surroundings.
• In extreme conditions of use, conductive dust can settle inside the machine. For this reason and for better safety, an on-site
SPE-PRCD or ground-fault circuit is required between the mains network and the machine, to be installed and tested if
necessary by a professional electrician.
• When working with the machine wear safety shoes (as per EN ISO 20345 at least S1), safety goggles (as per DIN EN 166 Class
2, basic strength S), snug-fitting safety gloves (as per DIN EN 388, Class 2 resistance to abrasion, cut resistance Class 3, tear
resistance Class 2, perforation resistance Class 3 and as per EN 407 at least Performance level 1 against contact heat) and
hearing protection (as per DIN EN 352-4 or comparable)..
• Operator age: The respectively valid country-specific laws/standards/guidelines/directives have to be followed.
• Do not use click-in socket outlets and click-in power plugs (blue CEE power plugs) for power connection, otherwise the
EMERGENCY STOP does not function. The user must check whether the power plug can be pulled out of the outlet by the
cable (shutdown, chap. 9.1, p. 64).
• Do not use angled power plugs.
NOTe!
[REV. 20210302] OC_RPG_L_BA_790038761_01__INH-02_EN
Information and safety instructions for the responsible body
The recommendations concerning "Personal protective equipment" only apply to the
product being described. Other requirements resulting from the ambient conditions on-site
or of other products, or from combining with other products, are not taken into account.
These recommendations do not in any way release the responsible body (employer) from its
statutory health and safety at work obligations towards its employees.
Orbitalum Tools GmbH D-78224 Singen www.orbitalum.com
eNGLISH
43