Hallde RG-400i Manual De Instrucciones página 5

CAPACITY
Up to 5 000 portions per day and 60 kg per
minute.
USING THE FEEDERS
MANUAL FEEDER, ERGO LOOP /
PNEUMATIC PUSH FEEDER:
These two feeders can be used for all types of
products, small and large.
Feed Cylinder A with three internal knives fix
and divide up the product during preparation
and is optimized for preparation of cabbage.
MANUAL FEEDER, ERGO LOOP
Feed Cylinder B with one internal wall is
optimized for manually orienting of products,
stacking.
THE FEED HOPPER:
Is used for continuous cutting of large quantities
of round products like potatoes, onions etc.
THE 4-TUBE INSERT:
Is used for cutting long products such as
cucumbers into slicers, see picture.
MANUAL PUSH FEEDER CHEESE
Feed Cylinder for Cheese with one internal wall
is optimized for orienting blocks of cheese for
preparation of shredded cheese.
ASSEMBLING AND
DISMANTLING
THE FEED CYLINDER (APPLIES TO ALL)
When fitting, fold down the locking handle.
Push the feed cylinder onto the hinge pins of
the machine, and lower the feed cylinder.
Raise the locking handle.
When removing, first remove the feed attach-
ment.
Lower the locking handle.
Remove the feed cylinder from the hinge pins
of the machine.
THE 4-TUBE INSERT
Press the stop button.
When fitting, fit feed cylinder A or B.
Place the 4-Tube Insert in the feed cylinder with
the shaft in the feed cylinder tube.
Press down the 4-Tube Insert and turn the
locking knob anti-clockwise.
When removing, turn the locking knob clock-
wise and remove the 4- tube insert.
THE MANUAL PUSH FEEDER
Press in the machine stop button.
When fitting, fit feed cylinder A or B.
Move the lever up all the way.
Fit the manual push feed attachment shaft
into the feed cylinder tube.
6
Press down the manual push feed attachment
and swing it in anti-clockwise.
When removing, press down the stop pad and
swing out the manual push feed attachment
clockwise and remove it.
THE PNEUMATIC PUSH FEEDER
Press in the machine stop button.
When fitting, fit feed cylinder A.
Fit the pneumatic push feed attachment shaft
into the feed cylinder tube.
Press down the pneumatic push feed attach-
ment and swing it anti-clockwise.
Push the compressor hose snap coupling onto
the pneumatic push feed attachment nipple.
Set the speed controls of the machine and of
the pneumatic push feed attachment to suit
the cutting tool being used as specified in the
instructions under the heading SETTING THE
SPEED CONTROLS.
Start the compressor and adjust its delivery
pressure to 5,5 bar. Handle the compressor in
accordance with the manufacturer's instruc-
tions.
Check the air pressure on the pressure gauge.
The recommended air pressure is 5 bar but the
actual value needed may vary. If the air pres-
sure reading on the pressure gauge is different,
pull the control upwards and then turn it until
the pressure gauge reading is 5 bar, and then
press it back down again.
When removing, switch off the compressor
and then disconnect the compressor hose
snap coupling from the pneumatic push feed
attachment nipple.
Press down the stop pad and swing out the
pneumatic push feed attachment clockwise,
and then remove it.
THE FEED HOPPER
Press in the stop button.
When fitting, fit the feed cylinder with two
internal guides.
Place the feed hopper in the centre of the feed
cylinder, with the shaft in the feed cylinder tube.
Press down the feed hopper and turn the
locking knob anti-clockwise.
When removing, turn the locking knob clock-
wise and remove the feed hopper.
THE MANUAL PUSH FEEDER, CHEESE
Press in the machine stop button.
When fitting, fit feed cylinder for Cheese
Shredder.
Move the lever up all the way.
Fit the manual push feeder Cheese Shredder
attachment shaft into the feed cylinder tube.
Press down the manual push feeder Cheese
Shredder attachment and swing it in anti-
clockwise.
When removing, press down the stop pad and
swing out the push feeder Cheese Shredder
attachment clockwise and remove it.
INSTALLATION OF CUTTING
TOOLS AND TRAY
While using the manual, pneumatic feeder
or manual push feeder cheese, make sure
the pusher plate is in the upper position and
swing it out the feeder to the left. If the feed
hopper or 4-Tube Insert is being used, lift the
shaft out of its mounting at the back of the
machine.
Lower the locking handle and tilt the feeder
backwards.
If the tray is to be used, the ejector plate is
placed in the bottom of the tray. Ensure that the
machine's knife housing has been thoroughly
cleaned. The tray, containing the ejector
plate, is then mounted around the shaft of the
machine's knife housing. Turn/push down the
ejector plate down into its coupling.
Place the chosen cutting tool on the shaft and
rotate the cutting tool so that it drops firmly
into its position.
When using Dicing Grid or French Fry Grid:
place the ejector plate in the bottom of the tray,
which is, in turn, mounted around the shaft of
the machine's knife housing. Turn the ejector
plate down into its coupling. Then mount the
chosen grid onto the shaft followed by the
slicer, ensuring that both fall properly into place.
Secure the agitator device when using the feed
hopper, the locking bolt when using the 4-Tube
Insert, or the decoring device when using the
manual, cheese or the pneumatic push feed
attachment, by turning them anti-clockwise by
means of the wrench onto the centre shaft of
the cutting tool.
REMOVAL OF THE CUTTING
TOOLS AND TRAY
Unscrew the screw cap, drill sleeve or lock
bolt clockwise using the key and remove the
cutting tool/tools, and the ejector plate together
with the tray.
SETTING THE SPEED
CONTROLS
The machine speed control is normally set to
position "2" for all cutting other than dicing,
when the speed control should be in position
"1".
When cutting with the pneumatic push feed,
set the speed control of the machine and
push feed attachment in accordance with the
following table.
PF = Pneumatic push feed attachment.
M = Machine.
HALLDE • User Instructions