Publicidad
Idiomas disponibles
Idiomas disponibles
The safety devices include (see chapter "Description of components"):
Pos: 11.8.2 7 /Inne ntei l/Si cherheit svors ch riften/Ha ndhab ung/ Siche rhe itsei nricht ung – Si cherheit ssc haltb ügel (1) Be nzi nmähe r +Text D LG @ 30\mod_ 140 4215 206 715 _6.docx @ 233 608 @ @ 1
–
Engine stop safety control bar (1)
The lawn mower is fitted with an engine stop device. During
operation and in the event of a hazard, the engine is switched off
by releasing the engine stop bar. The combustion engine and the
blade must come to a standstill within 3 seconds. After release,
the bar must always return to the position shown in the
"Description of components" diagram. If this is not the case, it
must be checked immediately by an authorised workshop.
Risk of injury!
If the stopping time of the blade is longer, stop using the device
and take it to an authorised workshop.
Measuring the stopping time
After starting the combustion engine, the blade rotates and a wind
noise can be heard. The stopping time corresponds to the
duration of the wind noise after the combustion engine has been
switched off; it can be measured with a stopwatch. The function of
the safety control bar must never be put out of operation. It is
important to make sure that the safety control bar functions
correctly. If this is not the case, have it repaired by an authorised
specialist workshop.
Pos: 11.8.2 8 /Inne ntei l/Si cherheit svors ch riften/Ha ndhab ung/ Schu tzei nricht ungen sind: @ 28\mod_ 138 493 7914 417 _6.do cx @ 21 8434 @ @ 1
The protective devices include (see chapter "Description of components"):
Pos: 11.8.2 9 /Inne ntei l/Si cherheit svors ch riften/Ha ndhab ung/ Schu tzei nricht ungen – Gehä use, Pra llble ch (8, 9)_ 52-PRO S A/5 2-S A @ 5 5\mod_1 542 2040 516 11_ 6.docx @ 593 574 @ @ 1
–
Housing, baffle plate (9)
These protective devices protect against injuries from objects that
are thrown upwards. The device must not be operated with a
damaged housing or without correctly attached baffle plate.
–
Housing
This protective device protects against injuries through contact
with the rotating cutter bar. The device must not be operated with
a damaged housing. Ensure that your hands and feet do not get
under the housing.
–
Belt drive covers (11), engine covers (5)
These protective devices protect against injuries through moving
parts. The device must not be operated with damaged covers or
without correctly attached covers.
–
Exhaust protection grill (6)
The engine/exhaust becomes very hot. The protection grill
protects the user against burns.
Do not operate the device without the exhaust protection grill.
The protective devices must not be modified.
Pos: 11.8.3 4 /Inne ntei l/Si cherheit svors ch riften/Ha ndhab ung/Grun dein stell ung de s Motors ni cht än dern @ 0\mod_ 1115 127 339 593_ 6.docx @ 209 @ @ 1
•
Do not change the basic settings of the engine or operate the engine at
excessive speed.
Pos: 11.8.3 5 /Inne ntei l/Si cherheit svors ch riften/Ha ndhab ung/ Beim Startvorga ng Ant rieb n ich t eins chal ten @ 0\mod _11 1512 742 825 0_6.do cx @ 21 1 @ @ 1
•
During the starting process, do not switch on the drive, if present.
Pos: 11.8.3 6 /Inne ntei l/Si cherheit svors ch riften/Ha ndhab ung/Inbet riebna hme ... Füße ... Siche rhei tsab stand zum Sch neidwerk zeug ... @ 0\mod_1 115 1275 484 37_ 6.docx @ 213 @ @ 1
When you start the machine, make sure that your feet are at a
sufficiently safe distance away from the cutting tool.
Pos: 11.8.3 7 /Inne ntei l/Si cherheit svors ch riften/Ha ndhab ung/Mas chine nic ht hoc hgekante t werden ... seitl iche r Auswu rf ... ni cht vo r Au swurfka nal ste hen @ 3 8\mod_1 439 902 0436 10_ 6.docx @ 407 289 @ @ 1
When the engine is started, the machine must not be tilted on end, if
necessary it must be tilted by pressing the guide bar down so that the
cutting tool is pointing in the direction away from the user, but only as
far as absolutely necessary. As long as the device has not been
lowered to the ground again, both of your hands must be on the top
part of the bar.
Do not start the engine when people or animals are standing in front of
the mower.
For devices with side ejection, do not start the engine when you are
standing in front of the ejection channel or there are other people or
animals in the ejection area.
Pos: 11.8.3 8 /Inne ntei l/Si cherheit svors ch riften/Ha ndhab ung/Hän de oder Füße nic ht in d ie Nähe von d rehen den Teile n Mäher (He ck +Sei te) @ 0\mod_ 111 512 8631 906 _6.do cx @ 21 7 @ @ 1
Never put your hands or feet near or under revolving parts. Always
make sure that your hands or feet do not get under the housing. For
devices with lateral ejection, always stay away from the ejection
opening.
Pos: 11.8.3 9 /Inne ntei l/Si cherheit svors ch riften/Ha ndhab ung/Kerzenste cker ab ziehen, Zü nds chlü ssel ab ziehe n (wenn vorha nden) Mähe r, kein Zünd sch lüs selsymb ol @ 4 2\mod_1 460 5415 255 80_ 6.docx @ 4355 89 @ @ 1
Stop the engine by releasing the engine stop bar, disconnect the plug
connector, make sure that all moving parts have come to a complete
standstill and the ignition key, if there is one, has been removed:
–
if you intend to leave the machine;
–
before you inspect, clean or carry out work on the machine;
–
before unblocking jams or removing blockages in the ejection
channel;
–
if a foreign body has been encountered.
–
when the machine starts to vibrate strangely.
Pos: 11.8.4 0 /Inne ntei l/Si cherheit svors ch riften/Ha ndhab ung/Frem dkörpe r: du rch Fach händle r p rüfen la ssen @ 0\mod_ 1115 129 6959 21_ 6.docx @ 223 @ @ 1
•
If a foreign object has been encountered or if the machine becomes blocked,
e.g. by driving onto an obstacle, an authorised workshop must check whether
parts of the device have been damaged or deformed. Always have any
necessary repairs done by an authorised workshop too.
Pos: 11.8.4 1 /Inne ntei l/Si cherheit svors ch riften/Ha ndhab ung/s tarke Vib ratio n: durch Fach händle r übe rprüfen @ 2 4\mod_1 376 572 0971 76_ 6.docx @ 182 607 @ @ 1
•
If the machine starts to vibrate unusually heavily or to make unusual noises,
please have it checked immediately by an authorised workshop.
Heavy vibrations on your hands can damage your health. Please contact an
authorised workshop immediately if heavy vibrations occur.
Pos: 11.8.4 2 /Inne ntei l/Si cherheit svors ch riften/Ha ndhab ung/ Bedien ungsa nleit ung ... Geräu sch pegel ... Schwi ngun gen ... Höc hstwe rte @ 2 8\mod_1 386 060 4561 10_ 6.docx @ 220 091 @ @ 1
•
WARNING
The noise and vibration levels shown in these operating instructions are the
maximum levels for use of the machine. The use of unbalanced cutting tools,
excessive speed of movement, or insufficient maintenance have a significant
influence on noise emissions and vibrations. Consequently, it is necessary to
take preventive steps to eliminate possible damage due to high levels of noise
and stress from vibration. Maintain the machine well, wear ear protection
devices, and take breaks while working. Adhere to the maintenance work listed
in this operating manual and have the device checked and serviced regularly by
an authorised workshop.
Pos: 11.8.4 3 /Inne ntei l/Si cherheit svors ch riften/Ha ndhab ung/Moto r abs tellen wen n ...Be nzi nmäher, Sei tenau swurf @ 38\mod_ 143 9899 710 956 _6.docx @ 405 609 @ @ 1
Stop the engine by releasing the engine stop bar, make sure that all
moving parts have come to a complete standstill and the ignition key,
if there is one, has been removed:
–
when you have to lift or tilt the mower e.g. for transportation;
–
when you need to transport the machine to and from the area to
be mown;
–
when driving off the lawn;
–
if you have to leave the machine for a short time;
–
if you want to adjust the cutting height;
–
before you fill it with fuel. Only refill when the engine is cold!
Pos: 11.8.4 4 /Inne ntei l/Si cherheit svors ch riften/Ha ndhab ung/ Benzinabs perrhahn sch ließen Mähe r @ 0\mod_1 1151 301 200 93_6. docx @ 2 29 @ @ 1
•
If the engine is equipped with a petrol shut-off valve, this should be closed after
mowing.
Pos: 11.9.1 / Innen teil/ Sic herhe itsvo rs chriften/Wa rtu ng und Lage rung/1 .1 Wa rtun g und Lage rung @ 0\mod_1 115 184 2598 75_ 6.docx @ 243 @ 2 @ 1
Maintenance and storage
Pos: 11.9.2 / Innen teil/ Sic herhe itsvo rs chriften/Wa rtu ng und Lage rung/U ngenüge nde Wa rtun g ..... si cherheit sreleva nten Mänge ln. @ 25\mod_ 1377 160 559 113_ 6.docx @ 186 917 @ @ 1
•
Insufficient device maintenance will lead to safety-related faults.
Pos: 11.9.3 / Innen teil/ Sic herhe itsvo rs chriften/Wa rtu ng und Lage rung/ Sch rau bverbi ndun gen fest ... sic here r Arbei tszu stan d ... @ 0\mod _111 518 435 2828 _6.do cx @ 24 5 @ @ 1
•
Ensure that all screws have been tightened securely and that the device is in a
safe working condition.
Pos: 11.9.4 / Innen teil/ Sic herhe itsvo rs chriften/Wa rtu ng und Lage rung/Ex plos ionsgefa hr, Gerät nich t mit gef üll tem Tank in ge sch losse nen Räumen auf bewahren @ 0\mod_ 111 5184 483 468_ 6.docx @ 247 @ @ 1
If the tank still contains petrol, never store a machine inside a building
where petrol fumes may come into contact with naked flames or sparks
or where they may ignite.
Pos: 11.9.5 / Innen teil/ Sic herhe itsvo rs chriften/Wa rtu ng und Lage rung/ Vorsic ht, he iß @ 0\mod _111 518 499 9140 _6.do cx @ 24 9 @ @ 1
The engine and exhaust reach very high temperatures during
operation. Allow the machine to cool down for at least 15 minutes
before starting any maintenance or cleaning work.
Pos: 11.9.6 / Innen teil/ Sic herhe itsvo rs chriften/Wa rtu ng und Lage rung/ Bra ndgefah r verme iden (Be im Hoc hkippe n oder auf d ie Se ite legen) @ 43\mod_ 146 667 3650 401 _6.do cx @ 49 9609 @ @ 1
•
To avoid a fire hazard, keep the engine, muffler (exhaust) and fuel tank free of
grass, leaves or escaping oil (grease). When tilting the machine upwards or
placing it on its side, make sure no oil or petrol escapes. Fire hazard! Allow the
engine to cool down before you store the machine in closed rooms. Do not
store the machine near open flames or sources of fire such as boilers or
heating systems.
Pos: 11.9.7 / Innen teil/ Sic herhe itsvo rs chriften/Wa rtu ng und Lage rung/vo r jedem Mähen ... Zu stand ...Me sse r(kupplu ng) prüfen Mähe r Ben zin mäher @ 19\mod _134 630 909 2301 _6.do cx @ 15 164 4 @ @ 1
Before using the machine, always check the condition and firm seating
of the blade. The blade fastening screw must always be tightened by an
authorised workshop. If the blade screw is tightened excessively or
insufficiently, blade coupling and cutter bar may be damaged or get
loose, which can lead to serious injuries. A worn or damaged blade
must imperatively be replaced.
The replacement, regrinding and balancing of the blade must be carried
out by an authorised workshop. Due to an incorrectly assembled blade
coupling, the cutter bar may become loose, which can lead to serious
injuries. An incorrectly ground and unbalanced blade can cause strong
vibrations and damage the lawn mower.
Pos: 11.9.9 / Innen teil/ Sic herhe itsvo rs chriften/Wa rtu ng und Lage rung/ Bes chädig te Teile e rset zen @ 0\mo d_11 151 860 7009 3_6. docx @ 2 61 @ @ 1
•
For reasons of safety, always replace worn or damaged parts.
Pos: 11.9.1 0 /Inne ntei l/Si cherheit svors ch riften/Wa rt ung un d Lage run g/Schut zhand sch uhe t ragen @ 0\mod_1 115 1861 954 68_ 6.docx @ 263 @ @ 1
Protective gloves must be worn at all times during maintenance and
cleaning work.
•
When handling operating fluids, such as engine oil and fuel, suitable protective
equipment (e.g. suitable protective gloves) must be worn. The data sheets of
the operating fluids must be observed.
Pos: 11.9.1 2 /Inne ntei l/Si cherheit svors ch riften/Wa rt ung un d Lage run g/Zü ndkerzens tecker a bziehe n Mäher @ 25\mod _13 7716 077 034 4_6.do cx @ 18 705 4 @ @ 1
5
Publicidad
