Publicidad
Idiomas disponibles
Idiomas disponibles
Before initial use
•
Check the oil level Y1 .
•
Check all screw connections for a tight fit.
•
Check the blade screw and have an authorised workshop tighten it, if
necessary.
•
Check whether the engine stop safety control bar is working properly.
•
Check whether the autodrive control bar is working properly.
•
Check that all protective devices have been attached properly and are not
damaged.
Pos: 19.6 /Innente il/Wartun gsin terval le/Vo r jedem Be trieb Be nzi ner Seitena uswu rf m.A. @ 34\mod _14 1033 719 757 3_6.do cx @ 24 801 2 @ @ 1
Before every operation
•
Check the lawn area and remove any objects.
•
Before and during the mowing process, check the area for live wires and
remove them, if possible.
Never drive over live wires when the cutting tool is switched on. Risk of electric
shock!
•
Check the area of the boundary wire (if an automatic mower is being used for
lawn care).
•
Check the oil level Y1 .
•
Check the condition and firm fit of the blade; have the blade screw tightened by
an authorised workshop, if necessary.
•
Check whether the engine stop safety control bar is working properly.
•
Check whether the autodrive control bar is working properly.
•
Check that all protective devices have been attached properly and are not
damaged.
After every operation
•
Clean the mower.
•
Check the blades for damage and wear.
Running-in time – after the first 5 operating hours
•
Change the engine oil.
Pos: 19.7 /Innente il/Wartun gsin terval le/Al le 10 Bet riebs stu nden Seitena uswu rf @ 22\mo d_1 3533 254 5446 9_6. docx @ 1 655 44 @ @ 1
Every 10 operating hours
•
Check all screw connections for a tight fit.
•
Check the blade coupling for wear and a tight fit.
Pos: 19.8 /Innente il/Wartun gsin terval le/Einfa hrze it – Na ch den e rste n 5 Betriebss tun den B& S @ 19\mod_ 134 6244 491 464 _6.docx @ 149 252 @ @ 1
Pos: 19.9 /Innente il/Wartun gsin terval le/Al le 50 Bet riebs stu nden Benziner, 52er P rofi, B& S @ 3 8\mod_1 4395 474 632 58_6. docx @ 4 053 16 @ @ 1
Every 50 operating hours
•
Change the engine oil.
•
Clean the air filter W .
•
Clean the spark plug and adjust the electrode distance Y .
•
Grease the bearings of the rear wheel drive R .
Pos: 19.10 / Innen teil/Wa rtu ngsi nte rvalle/Be i der Jah res inspek tion Benziner, mit Ant rieb ( B&S 800 E) @ 53\mod _151 359 982 5579 _6.do cx @ 57 964 9 @ @ 1
During annual servicing
•
Have the air filter replaced W .
•
Have the spark plug replaced Y .
•
Have the gearbox and the area under the belt cover cleaned.
•
Check the blade and re-grind and balance, if necessary; have it replaced, if
required.
•
Check all Bowden cables and have them set, if necessary.
Pos: 19.11 / Innen teil/Wa rtu ngsi nte rvalle/Nac h jedem Be trie b @ 19\mod _13 462 4310 665 4_6.d ocx @ 1 4888 0 @ @ 1
Pos: 20.1 /---------- 1 Leerzeile ---------- @ 0\mod_111 461 1787 140 _6.do cx @ 41 @ @ 1
Pos: 20.2 /Innente il/Pflege u nd Wartung des Mähe rs/1 PFLEGE U ND W ARTUN G DE S M ÄHER S @ 0\mod _11 1536 275 523 4_6.do cx @ 46 5 @ 1 @ 1
16 CARE AND SERVICING FOR YOUR MOWER
Pos: 20.3 /Innente il/Pflege u nd Wartung des Mähe rs/Pflege u nd Wa rtun g des Mähe rs H inweis @ 26\mod_ 137 717 1519 784 _6.do cx @ 18 974 7 @ @ 1
Regular care is the best way to guarantee a long service life and problem-free
operation! Insufficient device maintenance will lead to safety-related faults!
Pos: 20.4 /Innente il/Pflege u nd Wartung des Mähe rs/Orig inale rsat ztei le Hinwei s @ 6\mod _11 9978 847 128 5_6.do cx @ 43 482 @ @ 1
Only use original spare parts because only those guarantee safety and quality!
Pos: 20.5 /Innente il/Siche rhei tsh inweise/ Sic herhe itsh inweis: Lesen, Me sse r, Ste in, Moto rs top, Hei ss, Zündke rze, Ha nds chuhe @ 0\mod_ 1115 363 145 562_ 6.docx @ 469 @ @ 1
Pos: 20.6 /Innente il/Pflege u nd Wartung des Mähe rs/1.1 Rei nigu ng (Ab bild ung O ) @ 0\mod_ 1115 363 511 390_ 6.docx @ 471 @ 2 @ 1
Cleaning (figure O )
Pos: 20.7 /Innente il/Pflege u nd Wartung des Mähe rs/Reini gung Tex t Ben zin 52er S, 5 2-S A/52-PRO S A @ 38\mod _14 394 5843 181 5_6.d ocx @ 4 0468 7 @ @ 1
IMPORTANT
For cleaning and maintenance work, do not put the mower on the side, but tilt
it up at the front O (spark plug up); otherwise, starting difficulties may occur.
Secure the mower in the raised position!
ATTENTION
When tilting the machine upwards, ensure that no oil or fuel comes out of the
machine. Fire hazard!
Remove all dirt and grass directly after mowing. Use a brush or cloth to clean. Do
not turn the cutter bar as otherwise engine oil will be pumped into the carburettor/air
filter and starting difficulties may occur.
Safety information!
For explanation of symbols, see
the table on page 3
CAUTION
When not paying due care and attention, fingers may be crushed when
cleaning the live baffle plate.
IMPORTANT
Never clean the drive area, engine parts (like ignition system, carburettor,
etc.), seals and bearing points with a high-pressure cleaner or normal water
jet. Damages or expensive repairs can be the consequence.
Pos: 20.8 /Innente il/Pflege u nd Wartung des Mähe rs/1.1 Aufbewah ru ng @ 0\mod _11 153 6393 828 1_6.do cx @ 4 75 @ 2 @ 1
Storage
Pos: 20.9 /Innente il/Pflege u nd Wartung des Mähe rs/Aufbewahrung Text @ 0\mod_ 111 536 4661 953 _6.do cx @ 47 7 @ @ 1
Always keep the device in a clean condition in a closed, dry room out of reach of
children. Allow the engine to cool down before you store the machine in closed
rooms.
Pos: 20.10 / Innen teil/Pflege und Wa rtu ng des Mähe rs/1. 1 Umklappe n des Füh run gsho lmes (Abbil dung B4 ) @ 10\mod_ 1250 513 345 270_ 6.docx @ 865 05 @ 2 @ 1
Collapsing the guide bar (figure B4 )
Pos: 20.11 / Innen teil/Pflege und Wa rtu ng des Mähe rs/Umk lappen de s Führungs holmes Text 52-PRO S A/52- S A @ 55\mod_ 154 2209 620 219 _6.do cx @ 59 3870 @ @ 1
–
For space-saving storage or for transport, loosen the quick-release clamp or
knurled nuts until the top guide bar can be collapsed down to the engine
without resistance.
–
Do not kink or squeeze the Bowden cables while doing so.
CAUTION
When folding the bar for transport and storage, the bar may fold over
unintentionally when opening the quick-release clamp or when the knurled
nuts are released. In addition, this may result in crushed points between the
top and bottom of the bar. This may result in risk of injury.
Pos: null /Innen teil/ Vorbe reite nde Arbei ten/Kabel ni cht k nicken ode r eink lemmen W ICHT IG @ 5 8\mod_ 1567 149 3929 84_ 6.docx @ 604 682 @ @ 1
IMPORTANT
Make sure that the cables are not pinched, squeezed, twisted or overstretched
when the guide bars are folded apart or collapsed! Always run the cables
along the outside of the bar connection. A damaged cable may result in a
technical defect of the device.
Pos: 20.13 / Innen teil/Pflege und Wa rtu ng des Mähe rs/1. 1 Tra nspo rt u nd Siche run g des Ge rätes ( Abb ildu ng N + N4) @ 9\mo d_12 289 192 3106 7_6. docx @ 7 143 7 @ 2 @ 1
Transporting and securing the device (figure N + N4 )
Pos: null /Innen teil/Pflege u nd Wa rtun g des Mähe rs/T ransp ort und Sic heru ng Text 5 2er PRO S ab 2 015 @ 64\mod _158 082 369 2778 _6.do cx @ 62 642 2 @ @ 1
–
If the device has to be carried, hold it on the housing (1) at the front and on
the cross bar of the top part of the guide bar at the back or, if the bar is turned
down, on the cross bar of the lower part of the guide bar (2) (see figures N ).
Please take the weight of the machine into consideration before lifting it
(see Technical Data). Lifting large weights can result in health problems.
We recommend that this device should always be lifted or carried by at least
two people if other means of help are not available.
When the device is transported on a load area, a loading ramp should be used for
loading and unloading.
ATTENTION
Avoid injuries! Be especially careful when loading or unloading the
equipment. When a trailer is used, we recommend ensuring that it is equipped
with stable sidewalls. Only the marked points on the transport vehicle may be
used to secure the device.
–
Transport the device upright on all 4 wheels to avoid fuel loss, damage to the
equipment and personal injury.
–
Park the means of transport on level ground so that the device cannot roll away
before it is secured.
–
Secure the device with approved load-securing devices (e.g. tie-down straps
with clamping elements) on or inside the vehicle. Tie-down straps are belt
bands made of synthetic fibres. Every tie-down strap is marked with a label.
The label contains important details for application. The information on this
label must be heeded when using the tie-down strap.
–
For loaded goods that can roll, we recommend using direct strapping with four
lashing straps. For this purpose, the belts are fastened directly on the fastening
points on the device (see figure N4 ) and in the tie-down strapping points on
the loading surface and slightly pre-tensioned.
ATTENTION
Do not tighten the belts too firmly. Fixing the device too firmly can cause
damage.
Pos: 20.15 / Innen teil/Pflege und Wa rtu ng des Mähe rs/1. 1 Wartung des Messe rba lkens @ 0\mod_1 1153 655 097 65_6. docx @ 4 79 @ 2 @ 1
Servicing the cutter bar
Pos: 20.16 / Innen teil/Pflege und Wa rtu ng des Mähe rs/Wa rtu ng des Me sserbalkens Me sse rkuppl ung Text Ben zin @ 19\mod_ 134 624 6117 815 _6.do cx @ 14 946 4 @ @ 1
A sharp cutter guarantees perfect cutting performance. Before using the machine,
always check the condition and firm seating of the blade. The blade fastening screw
must always be tightened by an authorised workshop. If the blade screw is tightened
excessively or insufficiently, blade coupling and cutter bar may be damaged or get
loose, which can lead to serious injuries. A worn or damaged blade must
imperatively be replaced.
Pos: 20.17 / Innen teil/Pflege und Wa rtu ng des Mähe rs/1. 1 Nach sch leifen u nd Auswu chten de s Messe rbalke ns (Ab bild ung Q) @ 0\mod_ 111 5365 616 312 _6.docx @ 483 @ 2 @ 1
9
Publicidad
