MSA WinGrip AIO Instrucciones Para El Usuario página 3

EN
Prior to return to service MSA or a
1
Technician shall confirm, in writing,
that MSA WinGrip AIO has passed
examination.
WinGrip component disposal:
The stainless steel, aluminium, rubber
and plastic parts of MSA WinGrip AIOs
are recyclable. The harness and Energy
absorber lanyards shall be cut, to prevent
accidental use, and disposed of as
domestic waste.
UKCA type examination
SATRA Technology Centre Limited
Wyndham Way, Telford Way, Kettering,
Northamptonshire, NN16 8SD,
United Kingdom (Approved Body 0321)
UKCA conformity assessment
INSPEC International Ltd
56 Leslie Hough Way, Salford,
Greater Manchester, M6 6AJ,
United Kingdom (Approved Body 0194)
UKCA type examination and conformity
assessment in accordance with PPE
Regulation (EU) 2016/425 as retained in
UK law and amended, using harmonized/
designated standards.
The Declaration of Conformity can be found under the following link: MSAsafety.com/DoC
Product terminology
Component
EN
06 Read instructions
07
Model number
REF
08 Manufacturer
09 Vacuum anchor gauge
10 Test button
11 Alarm mute
12 Air inlet
13 Single User capacity
14 Standard
15
Serial number
SN
16 Vacuum outlet - used to install MSA
WinGrip Flying anchor (via Primary hose)
17 Notified body number
18 Carrying handle
19 Slide valve (on / off)
20 Supply pressure indicator
21 System side vacuum gauge
22 Cylinder lock release catch
23 Rotating arm with Energy absorber
lanyard
24
Date of manufacture
25 Plastic coated D-ring
26 Filling adaptor
Production control phase
CE type approval
Inspec International B.V.
(Notified Body No: 2849)
Beechavenue 54, 1119 PW,
Schiphol - Rijk, Netherlands
Notified bodies
CE type examination
SATRA Technology Europe Limited
(Notified Body No: 2777)
Bracetown Business Park
Clonee, D15YN2P
Republic of Ireland
Authorised representative
MSA Technologies and Enterprise Services
GmbH, Thiemannstr. 1, Berlin 12059,
Germany
4
Table 1: Pre-use examination
Item Function
MSA WinGrip Single point vacuum anchor.
AIO
Provides connection between the
REF 80000-03
vacuum anchor and the User via a
Energy absorber
Work positioning rope.
MSA WinGrip Used as a single point vacuum
Flying vacuum anchor during installation, or when
anchor working on an area that cannot be
accessed from the MSA WinGrip
AIO. The flying anchor may carry a
spare MSA WinGrip cylinder
Provides up to 6 hours use for a
01
single installation. Set to deliver
MSA WinGrip
compressed air at 115 psi. May be
Cylinder
filled by a Competent person (
filling adapter may be required). Has
an in-built pressure release valve
and safety burst disk (6500 psi).
Flexible re-enforced rubber tubing
02
with a male and a female connector.
Primary
vacuum hose
When used in combination with the
03
Energy absorber the harness can
MSA WinGrip
sustain the forces developed during
harness
a fall.
Used to secure the User to the
04 05
anchor point. Double ropes have the
Work positioning
advantage of attaching to two points
ropes
and are therefore required during
installation to provide 100% tie-off.
Pre-use checks
Ensure that the seal is clean and
intact.
Ensure that Energy absorber is
within date and that there is no
evidence of excessive wear.
Ensure that the seal is clean and
intact. Ensure the energy absorber
is undamaged and within service
life.
.
01
Ensure the cyclinder is filled, holding
the charge and within current
hydrostatic test.
26
Ensure that the hose is intact and
that the connector operates.
Examine in accordance with
manufacturer's instructions. Ensure
the MSA WinGrip harness is within
date.
Ensure that all Work positioning
ropes are intact and that the
connectors operate correctly.
Ensure the MSA WinGrip harness is
within date.
5