Cleco mPro300GCD-STO Serie Descripción Del Hardware página 10

1
EN
2.2 Symbols on the Product
Electric voltage
Read the operating instructions carefully
CE compliant
The product corresponds to the prescribed tech-
nical requirements in Europe.
Observe and comply with all local disposal
guidelines for all components of this equipment
and it's packaging.
TÜV SÜD tested (NRTL – Nationally Recog-
nized Test Laboratory)
The product complies with the prescribed tech-
nical requirements of the North American mar-
ket.
UKCA compliant.
The product corresponds to the prescribed tech-
nical requirements in Great Britain.
2.3 Intended Use
The user is liable for any damage caused by improper
use. Use the product only under the following conditions:
• Use only in industrial tightening processes.
• Repairs are only permitted personnel authorized by
Apex Tool Group. If the product is opened, the war-
ranty is voided. In the event of repair, send the com-
plete product to your Sales & Service Center.
Only in conjunction with the components listed in the
•
EU Declaration of Conformity.
Under the prescribed ambient conditions.
•
With the recommended supply voltage.
•
For power supply use only the power supply cable
•
supplied by Cleco.
• Within the power range, which is specified in the tech-
nical data.
In EMC Limit Class A (electromagnetic immunity for
•
industrial areas). For the currently observed EMC
standards, see the EU Declaration of Conformity.
2.4 Foreseeable misuse
► DO NOT bypass safety devices.
► DO NOT use the product in a potentially explosive at-
mosphere.
► DO NOT use the product in a humid environment or
outdoors.
► DONOT use the product in residential area).
1 Specialists are appropriately trained and experienced to
recognize potentially hazardous situations. You can take
10
► DO NOT use the product in conjunction with cutting
tools (drills, cutters, grinders...).
► DO NOT use the product for any tasks other than
tightening with the components specified in the Decla-
ration of Conformity.
► DO NOT use the controller as a climbing aid.
2.5 Operator Training
The fastening system may only be put into operation, set
up and maintained by personnel who have been trained
and qualified by the Apex Tool Group.
The product has been preset by the Apex Tool Group.
Changes to the factory settings may only be carried out by
a specialist
The owner/operator must ensure that new operating and
maintenance personnel are instructed in the operation and
servicing of the fastening system to the same extent and
with the same care.
Personnel undergoing schooling/training/instruction may
only work with the fastening system under the supervision
of an experienced person.
2.6 Personal Protective Equipment
► When working with rotating parts, it is not permitted to
wear gloves.
Recommendation: Freely rotating u-GUARD pro-

tected fastening tools from APEX.
► Wear suitable clothing. Do not wear loose clothing or
jewelry.
► Wear safety shoes.
► Wear protective goggles if there is a risk of dirt or
parts being ejected.
► Wear a hair net, if necessary.
2.7 Safety instructions relevant to the sys-
tem
It is imperative to observe the national, state and local reg-
ulations and standards.
► Do not make any changes to the controller, protective
devices or accessories without the prior written con-
sent of.Apex Tool Group.
► Do not open the controller or components of the con-
troller either for troubleshooting or other work. Any in-
tervention can cause serious injuries in case of a fail-
ure.
Risk of injury due to electric shock
In the event of a fault, the controller can carry voltage. An
electric shock can lead to cardiovascular arrest, respira-
tory failure, burns and serious injuries or death.
► Switch off the controller before connecting the power
supply and tool cables, when converting, unplugging
the plug connector, cleaning or decommissioning.
► Do NOT open the system components. After interrupt-
ing the power supply, a dangerous voltage may still
be present for 10 minutes.
► Do not operate the fastening system if the housing,
cable or tool is damaged.
► In the event of any malfunctions, never repair the fas-
tening system yourself without knowing how to do so!
appropriate safety measures and must comply with the ap-
plicable regulations
P2552HW | REV D l 2023-12
.
1
Apex Tool Group