Publicidad
Idiomas disponibles
Idiomas disponibles
1
EN
device must not cause an uncontrolled restart of the
system!
► Before switching the system on, check the function of
the emergency switching-off devices.
2.8
FCC- and IC Compliance
This product complies with Part 15 of the FCC Rules. Any
changes or modifications not expressly approved by the
manufacturer could void the user's authority to operate this
product. Operation is subject to the following two condi-
tions:
•
This product may not cause harmful interference.
•
This product must accept any interference received,
including interference that may cause undesired oper-
ation.
FCC Responsible party
Name: William Cain
Position: Director, R&D
Address: 670 Industrial Drive
Lexington, SC 29072
United States
Phone: +1 803 951 7558
Email: William.Cain@ClecoTools.com
This product has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide rea-
sonable protection against harmful interference when the
product is operated in a commercial environment. This
product generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to
radio communications.
Operation of this product in a residential area is likely to
cause harmful interference in which case the user will be
required to correct the interference at his own expense.
2.9
Certificates
Issuing
Certificate
agency
TÜV SÜD:
North America
NRTL
Certificate No.
Nationally Rec-
U8V 078313 0012 Rev. 00
ognized Test
Laboratory
Tested in accordance with
•
•
International
Certificate No.
DE 3 – 31655
Tested in accordance with
•
•
For product-relevant EC Directives, as well as the stand-
ards complied with, see the EC Declaration of Conformity.
12
UL 61010-1:2012/R:2018-11
CAN/CSA–C22.2
No. 61010‐1:2012/A1:2018‐11
IEC 61010-1:2010
IEC 61010-1:2010/AMD1:2016
P2552HW | REV D l 2023-12
3
Items Supplied
► Verify the scope of delivery for completeness on the
basis of dispatch papers.
•
Instruction manual
•
EU Declaration of conformity
•
Warranty
Controller
•
This Hardware Description
•
Quick Installation Guide
•
EC Declaration of Conformity
•
Warranty
•
Order no. SWB-S168300 – SD card + Software
•
•
Order no. 962190PT – Mating connector X9/X10 (2×)
•
Order no. 962405PT – Plug STO, bridged
•
Order no. 961893PT – Termination plug STO
Power Cord V Lock, varies by model:
•
Order no. 962276PT – mPro300GCD-STOEMEA
•
Order no. 962278PT – mPro300GCD-STONA
115 VAC
Order no. 962311PT – mPro300GCD-STOAPAC
•
4
Accessory
Order no. 962037-(...) – Cable TSnet
•
Order no. 961924-(...) – Cable STO cable
•
•
Order no. 960408-(...) – Cable PE
•
Order no. 962199PT – Housing for connector X9/X10
Power Cord V Lock
•
Order no. 962277PT – 230 VAC UK
Power Cord
•
Order no. 541683-02 – 230 VAC NA
5
Product Description
•
Controller for use with a NeoTek series corded hand
tool or a BD series fixtured spindle.
Control configurable for use as primary or secondary
•
control.
•
A total of up to 16 screw channels can be realized.
•
Controller with the suffix STO in the type name are
equipped with the STO safety function, see chapter 8
STO Safety Function, page 16
6
Pin Assignment
This chapter describes the Cleco specific connectors.
Standard plugs are not considered. All connectionsare
short-circuit proof.
X5 – Additional Devices
The inputs allow voltages from ‐15 V to +15 V.
All outputs provide RS232 conforming signals.
•
•
-
Voltages < 0.8 V correspond to a zero.
Apex Tool Group
Publicidad
