Nordcap MORETTI FORNI P Serie Manual Instrucciones página 22

- Remove the gasket.
- Replace the tempered glass (item 3 tab.A).
- Perform the above operations in reverse order to reassemble.
5.3.9.1 REPLACING THE HANDLE SPRING (LEFT)
After carrying out the operations described in 5.1 above, to replace the
handle spring proceed as follows:
- Remove the left side panel by unscrewing the four fixing screws.
- Disconnect the spring (item 14 plate A) by unscrewing the two fixing
nuts.
- Replace the spring, calibrating the tension with the two nuts.
- To remount the panel, perform these operations in reverse order.
5.3.9.2 REPLACING THE HANDLE SPRING (RIGHT, P150G)
After carrying out the operations described in 5.1 above, to replace the
handle spring proceed as follows:
- Unscrew the digital pyrometer screws (plate A);
- Unscrew the digital pyrometer box screws (plate A);
- Unfasten the screws (plate A) holding the right side panel;
- Lift the rock wool;
- Unfasten the nut (plate A) holding the spring;
- Replace the spring (plate A);
- Perform the above operations in reverse order to reassemble.
5.3.10 REPLACING THE REFRACTORY SURFACES
After carrying out the operations described in 5.1, to replace the upper and
lower refractory surfaces proceed as follows:
- Open the front door (item 4 plate A).
- Raise the upper refractory surface (item 28ab plate U) by prying it up
with a screwdriver.
- Raise perforated the lower refractory surface (item 28ab plate L) by
prying it up with a screwdriver.
- Replace the refractory surfaces.
- Perform these operations in reverse order to reassemble (procedure point
2.4.1).
5.3.11 REPLACING THE
THERMOSTAT
WARNING!
Regularly check that the safety thermostat is
operating correctly.
After carrying out the operations described in 5.1 above, to replace the
safety thermostat proceed as follows:
- Remove the two fixing screws.
- Disconnect the thermostat faston connectors.
- Remove the right side panel by unscrewing the four fixing screws.
- Open the front door (item 4 plate A) and loosen the two screws on the top
front part of the chamber that fasten the thermostat sensor.
- Remove the thermostat sensor, located inside the insulating rock wool,
cutting out the rock wool around it (fig. 24).
- Replace the thermostat (item 19 plate A) with its sensor and the worn
piece of rock wool, if necessary.
- Perform the above operations in reverse order to reassemble.
5.4 REPLACING PARTS
COMPARTMENT
5.4.1 REPLACING THE LIGHT BULB
After carrying out the operations described in 5.1 above, to replace the light
bulb and/or cover, proceed as follows from the inside of the leavening
compartment:
- Unscrew the cover (item A - fig.25) and replace the bulb (item B -fig.25)
and/or the cover.
- Screw the cover back in place
5.4.2 REPLACING THE DOOR KNOB
After carrying out the operations described in 5.1 above, to replace the ball
knob proceed as follows:
- Open the doors of the leavening compartment;
- Remove the plug;
- Unscrew the fixing nut inside the knob;
- Replace the knob (item 2 plate B) and tighten the fixing nut.
5.4.3 REPLACING THE THERMOSTAT
After carrying out the operations described in 5.1 above, to replace the
thermostat proceed as follows:
- Remove the electrical panel fixing screws.
- Disconnect the thermostat faston connectors.
- Remove the snap-on thermostat dial (item 5 plate B).
- Unscrew the ring nut (item 6 plate B) fixing the thermostat.
- Remove the thermostat sensor located inside the compartment.
- Replace the thermostat (item 7 plate B) and the relative sensor.
BAKING CHAMBER SAFETY
OF THE LEAVENING
- Perform the above operations in reverse order to reassemble.
5.4.4 REPLACING THE MAGNETIC DOOR FASTENER
After carrying out the operations described in 5.1 above, to replace the
magnetic door fastener proceed as follows:
- Open the doors of the leavening compartment;
- Remove the seal snap ring;
- Replace the magnetic door fastener.
5.4.5 REPLACING THE THERMOSTAT DIAL AND RING NUT
After carrying out the operations described in 5.1 above, to replace the
thermostat dial and/or relative ring nut, proceed as follows from the outside
of the compartment:
- Remove the snap-on thermostat dial (item 5 plate B).
- Unscrew the ring nut (item 6 plate B).
- Replace the ring nut and/or the dial.
5.4.6 REPLACING
AND/OR THE LIGHT SWITCH
After carrying out the operations described in 5.1 above, to replace the
yellow indicator light and/or the light switch proceed as follows:
- Remove the control panel fixing screws.
- Disconnect the faston connectors for both the yellow indicator and the
light switch.
- Replace the yellow indicator light (item 14 plate B).
- Replace the light switch (item 4 plate B).
- Perform the above operations in reverse order to reassemble.
5.4.7 REPLACING THE HEATING ELEMENTS
After carrying out the operations described in 5.1 above, to replace the
heating elements proceed as follows:
- Unscrew the heating element fixing screws.
- Disconnect the heating element supply wires.
- Remove the heating elements (item 10 plate B).
- Perform the above operations in reverse order to reassemble.
5.5 DISMANTLING
When the appliance or its parts are dismantled, the various components must
be divided according to type of material, and then disposed of in compliance
with current laws and regulations.
UK/9
THE YELLOW INDICATOR LIGHT