Adjusting Dolby Digital And Dts Digital Surround - JVC TH-A30 Manual De Instrucciones

Creating Realistic Sound Fields
DVD FM/AM
TUNER PRESET
DOWN
REW
B.SEARCH
2 3
TOP MENU
1
4
7
SLOW
D.R.C
ANGLE
REPEAT A-B REPEAT
CLEAR SEARCH
Adjusting Dolby Digital and
DTS Digital Surround
You can adjust the following settings while activating Dolby Digital
or DTS Digital Surround.
It is recommended that you make adjustments from your actual
listening point while listening to reproduced sounds.
– Output balance for the front speakers
– Output balance for the rear speakers
– Output level for the center speaker*
– Output level for the rear speakers*
– Output level for the subwoofer*
* The adjustment is separately memorized for Digital Multichannel
Surround (Dolby Digital and DTS Digital Surround), and for
Dolby Pro Logic.
Before you start, remember...
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 2 again.
1
Select and play a DVD encoded with Dolby
Digital or DTS Digital Surround.
Now, you are ready to start adjustments.
• To adjust the output balance for the front speakers and the rear
speakers, go to the next step.
• To adjust the output level for the center speaker, the rear speakers,
and the subwoofer, go to step
2
To adjust the output balance for the front
speakers and the rear speakers
1) Press SOUND repeatedly until one of
the following adjustment indications
appears on the display.
23
VCR
AUX AUX
CONTROL
UP
FF
VCR CHANNEL
TUNING
F.SEARCH
ENTER
VOLUME
MENU
RETURN MUTING
SOUND
SOUND
2 3
SETTING
5 6
PRO LOGIC
PRO LOGIC
8 9
SETUP TEST
0
DSP MODE
ZOOM D.R.C DSP MODE
PROGRAM
REMAIN SLEEP
3
.
SOUND
• Each time you press the button, the adjustment indication
on the display changes as follows:
00 F 00
Normal indication
(canceled)
00 F (Front) 00 : To adjust the output balance for the front
speakers.
00 R (Rear) 00 : To adjust the output balance for the rear
speakers.
• "00 F 00" and "00 R 00" are the initial setting (the output
balances are at the center position). If you have already
changed the setting, another value will appear.
2) Press 3 or 2 to adjust the
output balance.
3 : Decreases the left speaker
output, or restores the right
speaker output.
2 : Decreases the right speaker
output, or restores the left
speaker output.
• Each output balance changes from
OFF (silence), –06 (most reduction) to 00 (no reduction).
3) Repeat 1) and 2) for setting the other speaker.
3
To adjust the output levels for the center speaker,
the rear speakers, and the subwoofer
1) Press SOUND repeatedly to select the
"CEN," "REAR," or "SW."
• Each time you press the button, the adjustment
indication on the display changes as follows:
00 F 00
Normal indication
(canceled)
CEN (Center) : To adjust the output level for center
speaker (from –6 dB to +6 dB).
REAR
: To adjust the output level for rear
speakers (from –6 dB to +6 dB).
SW (Subwoofer) : To adjust the output level for subwoofer
(from –6 dB to +6 dB).
• "CEN 0dB," "REAR 0dB," and "SW 0dB" are the initial
settings. If you have already changed the settings, another
value will appear.
2) Press 3 or 2 to adjust the
output level.
3 : Increases the output level.
2 : Decreases the output level.
3) Repeat 1) and 2) for setting
the other speakers.
00 R 00 CEN
SW REAR
ENTER
SOUND
00 R 00 CEN
SW
REAR
ENTER