Assembling The Electric Hand Lawnmower; Setting The Cutting Height - Brill Electro 380 Manual Del Usuario

Only use authorised PVC
extension cables with the code
H05 RN- F or H05 VV- F. The
extension cable must not exceed
GB
15 meters in length.

5. Assembling the Electric Hand Lawnmower

5.1. Checking all parts are
included
The Electric Hand Lawnmower
box contains the following
parts:
Electric Hand Lawnmower
Node
1 upper section of the
guide handle
1 middle section of the
guide handle
1 lower section of the
guide handle
Assembly parts for the guide
handle in a plastic bag
1 thickness gauge
Operating instructions
5.2. Assembling the guide
handle
(fig. A – K)
1. Tilt your Hand Lawnmower
so that the black rollers face
upwards (fig. C).
Fit the lower section of the
guide handle (5) so that the
drilled holes (10) are over
handle bolts (11) (fig. B/C).
Note: Make sure that the
groove in the drilled hole (10)
and the locking tab of the
handle bolt (11) meet (fig. D).
Warning! Do not use excessi-
ve force. First ensure that the
recess in the handle and the
lug of the bolt are in align-
ment and then fix together.
2. Continue assembling the
guide handle as follows using
the black central connecting
section:
Disassemble the central
connecting section (19)
(referred to as the "node"
from now on).
20
Attention ! To prevent
A
injury, the Electric Hand
Lawnmower must not be used
for trimming bushes, hedges,
shrubs, for cutting and pruning
The front and rear sides of the
node are fastened together by
a clip lock to prevent them
from springing open. The
clip lock can be found in the
recess on the back of the
node. For easier disassembly,
release the clip lock by
pushing it outwards.
Press the four nuts into the re-
cesses in the rear section of
the node (the side without the
Brill logo). Gently press in the
four nuts so that they are
inserted properly and do
not fall out of the recesses
when the node is turned over
(fig. E).
Turn the mower so that the
rollers rest on the ground.
Prepare the top and middle
sections of the guide handle
so that the sections of the
handle overlap as shown in
the assembly diagram (fig. F).
Hold the rear section of the
node so that the grass catcher
holder (18) (fig. A) faces
upwards and guide the cable
through the cable duct on the
left side of the node (fig. G)
(viewed from below. Pay
attention to the length of the
cable!).
Now insert both sections of
the handle according to the
recesses (fig. H).
Attach the front section of the
node to the rear section of
the node. Make sure that you
hear the clip lock snap into
place and screw together both
parts of the node using the
bolts provided (fig. I/K).
3. Now attach the middle
and top sections of the
guide handle using the bolts
of climbers or grass on roofs
or in balcony boxes.
and wing nuts provided
(fig. L/M).
Warning ! The cable must
not hang down near the
cutting cylinder.

5.3. Setting the cutting height

(fig. N/O)
Warning ! To prevent injury,
A
never set the cutting height
when the motor is running.
Set the cutting height on the
Electric Hand Lawnmower as
follows:
1. Stand the Electric Hand Lawn-
mower on a flat, solid surface.
2. Position yourself in front of
the cutting height scale of the
Electric Hand Lawnmower
(fig. N).
3. Loosen both fixing nuts (9).
4. With both hands on the ad-
justing handles (12) set the
cutting height you require
(fig. O) :
Highest cutting height:
Lowest cutting height:
Note : Make sure that the
arrows marking the cutting
height (8) show the same
cutting height on both sides
of the scale (fig. O1).
5. Re-tighten both fixing nuts (9)
(fig. N).
Warning: Only set
A
the cutting height when
the motor is switched off.
When setting your Hand Lawn-
mower to a low cutting height,
ensure that the lower blade
and cutting cylinder do not
touch the ground if the ground
is uneven.
45 mm
14 mm