Maintenance / Care / Storage - Brill Electro 380 Manual Del Usuario

Blockage Protection/Safety
Clutch
If a foreign object blocks the
lawnmower blades or if the
motor is overloaded, the safety
clutch is activated automatically.
You will hear a rattling sound

8. Maintenance / Care / Storage

8.1. Maintenance
Maintenance includes all jobs
which keep your Electric Hand
Lawnmower in perfect working
order. By regularly checking
the unit (firm seating of screw
connections, cracks, damage)
and replacing defective or worn
parts you can prevent accidents
and failure.
Repairs may only be carried
out by Brill service centres or
dealers authorised by Brill.
Before adjusting or clean-
A
ing your Hand Lawnmower
always switch off your mower
and disconnect the mains plug
to ensure that your mower
cannot be switched on again
unintentionally!
Warning! Do not grasp mo-
A
ving cutting tools.
Care
To avoid injury to persons
A
and material damage :
Never clean your Electric Hand
Lawnmower with running water,
in particular with water under
high pressure.
After using the mower clean
with a moist cloth. Spray the
cutting cylinder and lower blade
with an oil of low viscosity
(e.g. spray oil).
(similar to the sound of a cord-
less screwdriver). Please unplug
the mains plug and remove the
foreign object. You can then
continue mowing as usual. If the
safety clutch is activated even
though there are no foreign
Maintenance
The blades, which if cared for
properly must only be sharpened
after years, can only be
sharpened by Brill due to
the special sharpening
technique.
The mower may only be repaired
and the cutting blades may only
be installed by approved special-
ist workshops.
Be particularly careful when
adjusting the blades so that you
do not trap your fingers between
the rotating blades and fixed
parts of the Electric Hand Lawn-
mower.
Note : Ensure that all nuts, bolts
and screws are tight and that the
mower is in good working order.
For safety reasons, allow all
worn out and damaged parts
to be exchanged by Brill Service
or authorised specialist dealers.
To avoid injury and damage to
the mower we recommend you
have your mower checked in
autumn so that it is ready and
safe to use next season.
Storage
Store your Electric Hand Lawn-
mower in a dry, cool place
where it is protected from frost.
The mower should be stored
out of the reach of children.
8.2. Adjusting the cutting tool
(fig. S/T)
The cutting tool of your Electric
Hand Lawnmower was set at an
objects blocking the cutting
cylinder, the cutting height you
have selected may be too low.
Select a higher cutting height
e. g. 45 mm and then select
a lower cutting height for the
second cut.
optimum setting before leaving
our factory. However, if the cut
is not clean after using your
mower for a longer period of
time, please correct the setting
of the lower blade as follows:
1. Switch off your Electric Hand
Lawnmower and disconnect
the mains plug to ensure
that your mower cannot be
switched on again uninten-
tionally.
Warning! Do not grasp
A
moving cutting tools.
2. Push the supplied thickness
gauge (24) on the left hand
side between one blade of
the cutting cylinder (1) and
the lower blade (2) (fig. S).
3. Turn the hexagon thread
bolt (25) with a 10 mm fork
wrench to the left or to the
right until the thickness gauge
closes slightly. Repeat this
on the right hand side of the
mower.
4. Turn the cutting cylinder to
test the setting. None of the
5 blades of the cylinder must
touch the lower blade.
Warning ! Handle the
A
cutting tool carefully
to avoid cutting yourself.
Wear appropriate gloves to
protect your hands.
5. When you have adjusted
the cutting tool test it using
a piece of newspaper
(fig. T).
GB
23