Hillrom NP100 Bidensity Instrucciones De Uso página 3

Proceed with the final steps before reusing the cleaned and
disinfected mattress (See "Performing the Final Steps",
page 3).
Cleaning and Disinfecting at Regular Intervals or
in the Event of High Risk of Contamination
Follow the same instructions as above (See "Cleaning and
Disinfecting after the Departure of a Patient or when Changing
the Sheets", page 2), but with the products listed below.
Using Recommended Products
After the departure of patients with infectious diseases:
• Dismozon® Pur (Bode)
Concentration: 40 g/l (= 4%), contact time: 1 h
After the departure of patients with Clostridium Difficile:
• Dismozon® Pur
Concentration: 15 g/l (= 1.5%), contact time: 2 h
• Anioxy-Spray WS (Anios)
Ready to use, contact time: 30 min
Dry Steam Cleaning the Mattress
Dry steam or superheated steam contains no more than 6% of
water in suspension and avoids the effects of condensation.
To avoid damage due to high pressure or an abnormal surface
temperature, take the following precautions:
• Do not use accessories such as high pressure hoses (A).
It is preferable to use soft non-metallic brushes (B) and
wipers (C) in such a way as to reduce the pressure to an
acceptable level.
• Do not brush and apply reduced pressure to labels and
markings.
• Dry carefully and look for signs of water ingress before
reusing.
Hill-Rom recommends the use of the Sanivap® method:
• Application time recommended by the supplier:
approximately 1 sec.
• Distance (recommended by the supplier) between the
source and the surface to be disinfected:
approximately 3 mm.
• Application: exterior parts of the mattress (covers).
• Frequency: for each new patient.
Machine Washing the Mattress Cover
Do not always machine-wash, as doing so will reduce the life
time of the components. Machine-wash only if particular risks
of infection occur.
Maximum temperature: 70°C
Delicates
Only clean with oxygenated agents
Do not iron
Do not dry clean
Can be tumble dried
Moderate temperatures: 50° C
1. Dismozon® Pur is listed by the V.A.H (Verbund für
Angewandte Hygiene e.V.).
© 2021 Hill-Rom Services, Inc. ALL RIGHTS RESERVED.
April 2021
1
A
B
C
Reinstalling the cover
When reassembling the cover after machine washing, make
sure to match with the associated foam (See "Mattress /
foam / cover combinations", page 3).
Orientate properly the cover on the foam regarding the
marking located on the foam in the feet area toward the top.
Mattress / foam / cover combinations
Ref.
Ref. Foam
Mattress
ASS029
ASS030
ASS031
ASS032
ASS038
ASS063
ASS035
ASS022XT
ASS079
Performing the Final Steps
• Always remove all traces of the products used when
washing or disinfecting the mattress.
• Make sure that all the parts of the mattress are perfectly
dry before installing to avoid any risk of condensation
forming inside the mattress.
Complying with Conditions for Transport and
Storage
Symbol
Temperature
Hygrometry
Atmospheric Pressure
*Applicable only if the mattress is transported or stored in its
original packaging.
The mattress must be stored in its original packaging:
• Protected against light and damp;
• At least 10 cm above floor level to prevent fluid ingress;
• Protected against dust;
• Outside passageways.
Never stack more than 15 mattresses.
164033(10) - EN
Ref. Cover
UPH029 TEX029
UPH030 TEX030
UPH031 TEX031
UPH032 TEX032
UPH038 TEX038
UPH063 TEX063
UPH035 TEX035
UPH022 TEX022XT
UPH079 TEX079
Feature
Transport / storage
-30°C to +50°C
20% - 85%
700 mbar - 1060 mbar
Dim. / cm
14 x 85 x 198
14 x 85 x 198
14 x 90 x 198
14 x 90 x 198
14 x 90 x 203
14 x 90 x 188
14 x 85 x 198
14 x 85 x 198
15 x 90 x 203
*
Page 3 - 4