GRAPHITE 59G886 Instrucciones De Uso página 9

GWARANCJA I SERWIS
Warunki gwarancji oraz opis postepowania w przypadku reklamacji
zawarte są w załączonej Karcie Gwarancyjnej.
Serwis Centralny
GTX Service tel. +48 22 573 03 85
Ul. Pograniczna 2/4 fax. +48 22 573 03 83
02-285 Warszawa e-mail graphite@gtxservice.pl
Sieć Punktów Serwisowych
i pogwarancyjnych dostępna
gtxservice.pl
GRAPHITE zapewnia dostępność części zamiennych oraz materiałów
eksploatacyjnych dla urządzeń i elektronarzędzi. Pełna oferta części
i usług na gtxservice.pl.
Zeskanuj QR kod i wejdź na gtxservice.pl
TRANSLATION OF
THE ORIGINAL INSTRUCTIONS
CERAMIC TILE SAW
59G886
CAUTION: BEFORE USING THE DEVICE READ THIS MANUAL
CAREFULLY AND KEEP IT FOR FUTURE REFERENCE.
DETAILED SAFETY REGULATIONS
Detailed safety conditions regarding use of saws for ceramic tile
cutting
• Power supply voltage must match value marked on the rating
plate of the ceramic tile saw.
• Connect the tile saw only to electrical system equipped with
residual current circuit breaker that will cut the power off when
earth leakage current exceeds 30 mA in less than 30 ms.
• When working outdoors use only extension cords designed for
outdoor use.
• During operation of the tile saw strictly follow applicable
regulations regarding occupational health and safety.
• Make sure direction of cutting blade rotation matches indicated
direction of the saw motor.
• Cutting blade of the saw should be free to rotate after installation.
• Always use anti-splinter goggles, hearing protection and anti-dust
mask.
• Always wear proper clothing for your work! Loose items of
clothing or jewellery might get caught by rotating cutting blade.
• Before any adjustment, measurement, cleaning or removing
jammed ceramic pieces always disconnect power supply from
the tool with the switch and remove the plug from mains socket!
• After repair or maintenance is carried out, install all shields and
protective parts before switching on the tile saw.
• Do not start working with the tile saw when tired or under
influence of medicines.
• It is vital that all persons who operate the tile saw are properly
trained for operation, using and adjustments of the tile saw.
• Replace damaged protection parts immediately.
• Never overload the tile saw, causing rotational speed to drop
down considerably.
do napraw gwarancyjnych
na platformie internetowej
• Keep the workplace clean. Before working remove waste material
and unnecessary objects.
• Keep bystanders away from the tile saw workplace.
• Keep the workplace well illuminated.
• Do not distract person who is working with the tile saw.
• After the motor is switched off with the switch, never attempt to
stop the cutting blade by applying side pressure.
• Immediately replace damaged cutting blade.
• Never use cutting blades with parameters different from specified
in this manual.
• Never attempt to remove or disconnect protection parts of the
tile saw.
• When a break in work is required, finish current cutting and switch
off the tile saw.
• When a break in work and leaving the workplace is required,
switch off the tile saw with the switch and disconnect it from
power supply by removing the plug from mains socket.
• Check technical condition of the tile saw before starting to
operate:
- all protection parts must be in good working order and operate
as supposed to,
- screws and other mount parts must not be loosened,
- all adjustment keys must be removed from the tool.
• Always ensure the processed material adheres to the work table of
the saw with its whole surface.
• Never cut several pieces of material at a time.
• Do not unplug the tile saw from mains socket by pulling the
cord. Protect the power cord against excessive heat, oil and sharp
edges.
• When operating the tile saw keep your body in firm, standing
position.
• All parts of the tile saw must be properly fixed.
• Repairs of the tile saw should only be carried out by qualified
person in authorized service workshop and with use of original
spare parts.
• Do not make profile cuts with the tile saw.
• When carrying the tile saw, hold only by transport handles, do not
hold by saw shields.
SAFETY RULES FOR LASER DEVICE
Laser device used in the saw design is the class 2 with maximum
power below 1 mW and wavelength λ = 650 nm. Such device is not
dangerous to your eyes, however do not look directly at the source
of the light (temporary blindness hazard).
WARNING. Do not look directly at the source of laser beam. It
may cause hazards. Follow the below safety rules.
• Use the laser device in accordance with the manufacturer's
instructions.
• Do not, either intentionally or unintentionally, point the laser
beam at people, animals or any object other than processed
material.
• Do not bring to accidental pointing the laser beam at bystanders'
or animals' eyes for a period longer than 0.25 second, for instance
by pointing the laser beam at mirrors.
• Always ensure the laser beam is directed at material which does
not have any reflective surfaces.
• Reflective steel sheet (and other materials with reflective surface)
does not allow for laser use, because it might cause hazardous
light reflection directed at operator, bystanders or animals.
• Do not replace laser unit with device of other type. All repairs must
be carried out by the manufacturer or authorized person.
9
LASER LIGHT, LASER RADIATION
DO NOT LOOK AT THE LASER BEAM
LASER DEVICE CLASS 2
Wavelength: 650 nm; Output: < 1 mW
EN 60825-1:2007