Preparation For Operation - GRAPHITE 59G886 Instrucciones De Uso

CAUTION: Adjustments other than described in this manual put in
danger of exposition to laser radiation!
CAUTION! This device is designed to operate indoors.
The design is assumed to be safe, protection measures and
additional safety systems are used, nevertheless there is always a
small risk of operational injuries.
CONSTRUCTION AND USE
Ceramic tile saw is designed for wet cutting of ceramic tiles and
similar materials, appropriate in size for the size of the tile saw. The
tile saw must not be used for cutting wood or metal. When working
with the tile saw, use only cutting blades designed for this type of
tools. Ceramic tile saw is designed for all works from the range of
individual, amateur activities (tinkering).
Use the tool according to its purpose only.
DESCRIPTION OF DRAWING PAGES
Below enumeration refers to the device elements depicted on the
drawing pages of this manual.
Locking knob for cutting length limiter
1.
Handle
2.
Head
3.
Bevel locking knob
4.
Base
5.
Leg
6.
Fence
7.
Knurled head screw
8.
Locking knob of the mitre gauge
9.
Mitre gauge
10.
Work table
11.
Cutting blade
12.
Cutting blade shield
13.
Laser
14.
Head locking knob
15.
Transport screw
16.
Bevel angle scale
17.
Switch
18.
Leg fixing screw
19.
Water pump
20.
Laser switch
21.
Battery compartment
22.
Head locking screw
23.
Power indicator
24.
RESET button
25.
TEST button
26.
* Differences may appear between the product and drawing.
MEANING OF SYMBOLS
CAUTION
WARNING
ASSEMBLY/SETTINGS
INFORMATION
EQUIPMENT AND ACCESSORIES
Base
1.
Leg
2.
Mitre gauge
3.
Cutting length locking unit + knob - 2 sets
4.
Ring spanner
5.
Screw
6.
Knurled head screw
7.

PREPARATION FOR OPERATION

Ceramic tile saw is supplied disassembled. Take items out of the
package and assemble in the below described order.
- 1 pce
- 4 pcs
- 1 pce
- 2 pcs
- 4 pcs
- 2 pcs
10
CERAMIC TILE SAW ASSEMBLY
• Use the screws (included) to attach the legs (6) to the base (5)
(fig. A).
• Put the saw in the base (5). Be careful to fix the water pump (21) in
appropriate place of the base (fig. C).
• Attach the locking knobs for cutting length limiter (1) (fig. D).
• Use knurled head screws (8) to join the mitre gauge (10) to the
fence (7) (you can install the mitre gauge on both sides of the work
able) (fig. H).
• Unscrew the head locking knob (15) (fig. E) and the transport
screw (16) (fig. F).
• Unscrew the head locking screw (26) (fig. J).
Before using the tile saw unscrew the head locking knob and
remove the transport screw, otherwise moving the head with
cutting blade will be impossible. The water pump should be
immersed in water during cutting.
OPERATION / SETTINGS
Ensure the table saw is disconnected from power supply
network before starting any adjustments. To ensure safe, precise
and efficient tile saw operation, proceed with all adjustment
procedures as a whole.
After finishing all the setting and adjustment procedures
ensure that all adjustment keys are collected. Check that all
threaded joining elements are properly tightened. When making
adjustments ensure that all external parts work properly and
are in good condition. Any worn out or damaged part must be
replaced by qualified personnel before starting to use the table
saw.
Plug of the power supply cord of the tile saw is equipped with
residual current protection device. Check operation of the
residual current device before starting to use the tool.
• Put the plug into power supply socket, the power indicator (27)
will switch on (fig. O).
• Press TEST button (29) – the power indicator (27) will switch off.
• Press RESET button (28) – the power indicator (27) will switch on
again.
If the residual current device is faulty (it does not operate as
described above) you must remove power cord plug from the
power supply socket and give the tool for repair to authorized
service workshop.
SWITCHING ON / SWITCHING OFF
The mains voltage must match the voltage on the rating plate of
the saw.
Switch on the tile saw only when the material that is to be cut is
away from the cutting blade.
Switching on – press the button I of the switch (18) (fig. G).
Switching off – press the button O of the switch (18).
CUTTING
Water pump, power cord and water supply hose must be outside
of the cutting area.
Cutting blade must rotate with maximum rotational speed before
the cut is started. Wait until cooling water stream reaches the
cutting blade.
Base of the mitre gauge (10) is also the longitudinal fence.
• Set 0 angle on the mitre gauge (10) and tighten the locking knob
0
of the mitre gauge (9).
• Use knurled head screws (8) to attach the mitre gauge (10) to the
fence (7) (fig. H).
• Use scale on the fence (7) to set appropriate dimension.
• Press ceramic tile to the fence (7) and the base of the mitre gauge
(10) (fig. I).
• Press the 'I' button of the switch (18) and wait until water appears
on the cutting blade (12).