Aligning The Running Belt; Adjusting The Belt Tension - Tunturi Pure Treadmill 3.1 Manual Del Usuario

LUBRICATE THE RUNNING DECK
ACCORDING TO THE FOLLOWING
INSTRUCTIONS:
1. Attach the nozzle of the lubrication
tube to the T-Lube S container.
2. Lift the running deck and lock it.
3. Position the nozzle between the belt
and the board. Try to reach the spray
as far into the center of the running
deck as possible.
4. Spray the lubricant for 2-3 seconds.
5. Lower the running deck into its
normal position. Use treadmill for
your training session. Or allow the
treadmill to run for at least 5 minutes
at 5 KM/H (3 Mile/H).
NOTE!
Lubricate your treadmill only with T-Lube
S silicon lubricant. Contact your local
Tunturi distributor for further supplies
of T-Lube or further information on
lubrication and maintenance.

ALIGNING THE RUNNING BELT

Monitor belt tracking during exercise and
make adjustments as needed. The belt
should run in the center of the treadmill.
Alignment is not usually needed,
provided
• The treadmill is placed on an even,
solid and horizontal surface and the
belt is correctly tensioned
• The alignment of the belt is correct
It is, however, possible for the belt
to be pushed to one side due to the
user's running style (e.g. more weight
on one foot). The alignment of the
belt is adjusted by turning the two
bolts at the back of the treadmill.
ALIGN THE BELT ACCORDING TO
THE FOLLOWING INSTRUCTIONS:
1. Turn the power switch on and
increase the treadmill's speed to 5
km/h (3 mph).
2. If the belt drifts to the left, turn the left
adjustment bolt 1/4 turn clockwise
and the right adjustment bolt 1/8 turn
anti-clockwise. If the belt drifts to the
right,
All manuals and user guides at all-guides.com
turn the right adjustment bolt 1/4 turn
clockwise and the left adjustment bolt
¼ turn anti-clockwise.
3. If the belt remains centered the
adjustment is correct. If not, continue
to make small adjustments as above
until the belt is correctly aligned.
If the belt is allowed run across to
one side for long periods of time the
edges of the belt may be damaged
and the treadmill may not continue to
operate correctly. Any damage to the
belt caused by the lack of necessary
adjustment will not be covered by the
warranty.

ADJUSTING THE BELT TENSION

The belt must be tensioned if it begins
to slip on the rollers. In normal use,
however, keep the belt as loose as
possible! The belt tension is adjusted
by turning the same screws as used for
aligning the running belt. If turning the
screws will not effect the belt tension,
please contact your local Tunturi dealer.
1. Increase the treadmill's speed to 5
km/h (3 mph).
2. Turn both adjustment screws an
equal amount, ¼ turn clockwise.
3. Try to slow the belt down by holding
onto the handrails and braking as
you walk (as if you were walking
downhill).
If the belt slips, turn another 1/4 turn and
repeat the test. When braking heavily the
belt may slip. If the belt keeps slipping
despite repeated adjustments, please
contact your local Tunturi dealer.
power switch on to reset the treadmill.
This should clear incidental errors and
ready the treadmill for normal operation
again. If after you have reset the
treadmill by turning the power switch off
and on again, and the treadmill is still not
operational, contact your local Tunturi
dealer for service.
If you require spare parts, always
give the model, serial number of your
equipment and the spare part number
for the part you need. The spare part list
is at the back of this manual. Use only
spare parts mentioned in the spare part
list.
•
O W N E R ' S M A N U A L P U R E R U N 3 . 1
GB
13