Aligning The Running Belt; Adjusting The Belt Tension; Malfunctions; Error Codes - Tunturi T90 Manual Del Usuario

In average domestic use (a maximum of 60 minutes a
day), you should check the lubrication approximately
after every 300 hours of use – however, lubricate the belt
only if needed. The console is equipped with a counter
for measuring total values, thus allowing you to monitor
your total training time on the treadmill. If there is
any jerky movement of the belt, always check the
lubrication level. To do this, let the treadmill come to a
complete stop, then simply lift the running belt to feel
the running deck; if the deck feels dry and there is very
little evidence of lubricant on your hand, lubricate the
running deck according to the following instructions:
1. Attach the nozzle of the lubrication tube to the T-
Lube S container.
2. Adjust the running deck to its maximum elevation
(10 %).
3. Position the nozzle between the belt and the board.
Try to reach the spray as far into the center of the
running deck as possible.
4. Spray the lubricant for 5 seconds.
5. Lower the running deck into its normal position.
Let the belt run for at least a minute at 1,5 kph. This is
done to lubricate the belt evenly.
NOTE! Lubricate your treadmill only with T-Lube S
silicon lubricant. Contact your local Tunturi distributor
for further supplies of T-Lube.

ALIGNING THE RUNNING BELT

Monitor belt tracking during exercise and make
adjustments as needed. The belt should run in the
center of the treadmill. Alignment is not usually needed,
provided
•
the treadmill is placed on an even, solid and
horizontal surface and the belt is correctly tensioned
•
the alignment of the belt is correct
It is, however, possible for the belt to be pushed to one
side due to the user's running style (e.g. more weight
on one foot). The alignment of the belt is adjusted by
turning the two bolts at the back of the treadmill.
Align the belt according to the following instructions:
1. Turn the power switch on and increase the treadmill's
speed to 5 km/h (3 mph).
2. If the belt drifts to the left, turn the left adjustment
bolt ¼ turn clockwise and the right adjustment bolt 1/8
turn anti-clockwise. If the belt drifts to the right, turn
the right adjustment bolt ¼ turn clockwise and the left
adjustment bolt ¼ turn anti-clockwise.
3. If the belt remains centered the adjustment is correct.
If not, continue to make small adjustments as above
until the belt is correctly aligned. If the belt is allowed
run across to one side for long periods of time the edges
of the belt may be damaged and the treadmill may not
continue to operate correctly. Any damage to the belt
caused by the lack of necessary adjustment will not be
covered by the warranty.
O W N E R ' S M A N U A L

ADJUSTING THE BELT TENSION

The belt must be tensioned if it begins to slip on the
rollers. In normal use, however, keep the belt as loose
as possible! The belt tension is adjusted by turning the
same screws as used for aligning the running belt. If
turning the screws will not effect the belt tension, please
contact your local Tunturi dealer.
1. Increase the treadmill's speed to 5 km/h (3 mph).
2. Turn both adjustment screws an equal amount, ¼
turn clockwise.
3. Try to slow the belt down by holding onto the
handrails and braking as you walk (as if you were
walking downhill).
If the belt slips, turn another ¼ turn and repeat the test.
When braking heavily the belt may slip. If the belt keeps
slipping despite repeated adjustments, please contact
your local Tunturi dealer.

MALFUNCTIONS

NOTE! Despite continuous quality control, defects and
malfunctions caused by individual components may
occur in the equipment. In most cases it's unnecessary
to take the whole device in for repair, as it's usually
sufficient to replace the defective part. Always give
the model, serial number of your equipment and in
case of malfunctions also conditions of use, nature of
malfunction and any error code.
When you encounter unusual behavior from the
treadmill, simply turn the power switch off, wait 1
minute and turn the power switch on to reset the
treadmill. This should clear incidental errors and ready
the treadmill for normal operation again. If after you
have reset the treadmill by turning the power switch off
and on again, and the treadmill is still not operational,
contact your local Tunturi dealer for service.
If you require spare parts, always give the model, serial
number of your equipment and the spare part number
for the part you need. The spare part list is at the back
of this manual. Use only spare parts mentioned in the
spare part list.

ERROR CODES

The user interface will display information about
operational faults.
SYSTEM CHECK FAILED - Possible motor controller
fault. Turn the power switch off, wait 1 minute and
turn the power switch on again. If treadmill recovers
to normal operation, you may continue to use the
treadmill. Otherwise, call the dealer for service.
SPEED SENSOR ERROR - Call the dealer for service.
MOTOR SPEED ERROR - Ensure correct usage of
the treadmill. Do not push the belt with your feet.
Turn the power switch off, wait 1 minute and turn the
power switch on again. If treadmill recovers to normal
operation, you may continue to use the treadmill.
Otherwise, call the dealer for service.
GB
•
T 9 0
11