Settings After Connections (Input1, 2, 5) - Pioneer PDP-5004 Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Settings After Connections
(INPUT1, 2, 5)
After components have been connected to INPUT1,
INPUT2 or INPUT5, on-screen setup is necessary.
Follow the procedure described below and make settings
as they apply to the type of components connected.
[SIGNAL FORMAT] (INPUT1)/
[COLOR DECODING] setup
(INPUT1, 5)
Notes
÷ These settings are required (for INPUT1) only when providing
input signals with the following refresh rates: 1 31.5 kHz
horizontal / 60 Hz; 2 45 kHz horizontal / 60 Hz vertical; 3 48.4
kHz horizontal / 60 Hz vertical or 56.1 kHz horizontal / 70 Hz
vertical. Adjustment for other signal frequency formats is
performed automatically, so no manual setting is required
(Setting [SIGNAL FORMAT] is not possible).
÷ The [COLOR DECODING] setting is not supported when
inputting a computer signal, or when the [SIGNAL FORMAT]
function has been used to select a signal other than [480p] or
[720p].
÷ Perform [COLOR DECODING] settings individually for INPUT1
or INPUT5.
÷ [SIGNAL FORMAT] setting is possible when only INPUT1 is
selected.
Remote control unit
1
Select INPUT1, or INPUT5.
2
Press the MENU button to display the menu screen.
STANDARD
PICTURE
SCREEN
CONTRAST
BRIGHTNESS
COLOR
TINT
SHARPNESS
MPEG NR
DNR
CTI
COLOR TEMP.
PICTURE RESET
ENTER
SET
MENU
2/3
SET
5/∞
INPUT1
SETUP
OPTION
:
0
:
0
:
0
:
0
:
0
:
ON
:
MID
:
ON
:
MID
EXIT
MENU
3
Use the 2/3 buttons to select [SETUP].
STANDARD
PICTURE
SCREEN
PURECINEMA
CLAMP POSITION
SIGNAL FORMAT
COLOR DECODING
HDMI INPUT
SET
ENTER
4
Use the 5/∞ buttons to select [SIGNAL FORMAT],
then press the SET button. (INPUT1)
STANDARD
PICTURE
SCREEN
PURECINEMA
CLAMP POSITION
SIGNAL FORMAT
COLOR DECODING
HDMI INPUT
5
Use the 2/3 buttons to select the display mode.
S I G N A L F O R M AT
SET
SET
1 When the input signal has a refresh rate of 31.5 kHz
horizontal / 60 Hz vertical, pressing 2/3 will cause
the display mode to change alternately as follows:
3 480p 2
3 WVGA 2
2 When providing input signals with refresh rates of
45 kHz horizontal / 60 Hz Vertical, pressing the 2/3
buttons causes the display mode to alternate as
follows:
3 720p 2
[720-PC] indicates resolution of 1280 x 720.
3 When the input signal has a refresh rate of 48.4
kHz horizontal / 60 Hz vertical, or 56.1 kHz
horizontal / 70 Hz vertical, pressing 2/3 will cause
the display mode to change alternately as follows:
3 XGA 2
3 PC AUTO 2
If the [PC AUTO] setting is selected, screen
resolution will automatically switch between [XGA]
and [WXGA] as required.
System Settings
INPUT1
SETUP
OPTION
:
OFF
:
AUTO
:
480p
:
COMPONENT
MENU
EXIT
INPUT1
SETUP
OPTION
:
OFF
:
AUTO
:
480p
:
COMPONENT
:
480p
EXIT
MENU
3 VGA 2
3 720-PC 2
3 WXGA 2
21
EN

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Pdp-5014Pdp-4304Pdp-4314

Tabla de contenido