Three-Phase 400 V Class - Omron Q2 Serie Instrucciones De Instalación Y Funcionamiento

Model Terminals
R/L1, S/L2, T/L3
U/T1, V/T2, W/T3
-, +1
2360
2415
+3
*1 For IP20 protection, use wires that are in the range of applicable gauges. If your installation does not need IP20 protection, smaller
cables can be used.
*2 Remove insulation from the ends of wires to expose the length of wire shown.
*3 For wire gauges more than 30 mm
*4 Install an RCM/RCD with this wire gauge to maintain compliance with IEC/EN 61800-5-1:2007.
*5 Terminals - and +1 have two screws. The Recommended Gauge is the wire gauge for one terminal.
*6 A junction terminal is necessary to connect a braking unit (CDBR-series) to terminals - and +3.
■

Three-Phase 400 V Class

Model Terminals
R/L1, S/L2, T/L3
U/T1, V/T2, W/T3
4002
4004
-, +1, +2
4005
4007
B1, B2
4009
4012
R/L1, S/L2, T/L3
U/T1, V/T2, W/T3
-, +1, +2
4018
B1, B2
R/L1, S/L2, T/L3
U/T1, V/T2, W/T3
4023 -, +1, +2
B1, B2
TOMPYEUOQ2A03C AC Drive Q2A Installation and Operation Instructions
Applicable Gauge
Recommended Gauge
IP20
mm 2 mm
(AWG kcmil) (AWG kcmil)
120 × 2P 150 × 2P
(250 × 2P) (250 - 300 × 2P)
120 × 2P 185 × 2P
(250 × 2P) (300 - 400 × 2P)
70 × 2P 50 - 95 × 2P
(3/0 × 2P) (1/0 - 4/0 × 2P)
120 120 - 240
(1) (1 - 350)
2
, tighten to a tightening torque of 4.1 N∙m to 4.5 N∙m (36 lb.∙in. to 40 lb.∙in.).
Applicable Gauge
Recommended Gauge
mm 2
(AWG kcmil) (AWG kcmil)
2.5
(14)
2.5
(14)
2.5
(14)
*4
2.5
(10)
2.5
(10)
4
(8)
2.5
(14)
*4
2.5
(10)
6
(8)
4
(10)
6
(8)
2.5
(12)
*4
6
(10)
Wire Stripping
*2
Length
*1
Terminal Screw
2
mm
-
-
-
-
Wire Stripping
*2
Length
*1
IP20
mm 2
mm
2.5 - 10
10
(14 - 6)
2.5 - 16
18
(14 - 3)
2.5 - 4
10
(14 - 6)
2.5 - 10
-
(14 - 6)
2.5 - 10
10
(14 - 6)
2.5 - 16
18
(14 - 3)
2.5 - 4
10
(14 - 6)
2.5 - 10
-
(12 - 8)
2.5 - 10
10
(14 - 6)
2.5 - 10
10
(14 - 6)
2.5 - 16
18
(14 - 3)
2.5 - 4
10
(14 - 10)
4 - 10
-
(12 - 8)
6 Attachments
Tightening
Torque
N∙m (lb.∙in.)
35
(310)
M12
35
(310)
M12
35
(310)
M12
32 - 40
(283 - 354)
M12
Tightening Torque
Terminal
Screw
N∙m (lb.∙in.)
1.5 - 1.7
(13.5 - 15)
M4
2.3 - 2.5
*3
(19.8 - 22)
M5
1.5 - 1.7
(13.5 - 15)
M4
1.2 - 1.5
(10.6 - 13.3)
M4
1.5 - 1.7
(13.5 - 15)
M4
2.3 - 2.5
*3
(19.8 - 22)
M5
1.5 - 1.7
(13.5 - 15)
M4
2.0 - 2.5
(17.7 - 22.1)
M5
1.5 - 1.7
(13.5 - 15)
M4
1.5 - 1.7
(13.5 - 15)
M4
2.3 - 2.5
*3
(19.8 - 22)
M5
1.5 - 1.7
(13.5 - 15)
M4
2.0 - 2.5
(17.7 - 22.1)
M5
135
EN