Siemens SINUMERIK 802D sl Manual De Instrucciones página 11

30200, 4–90
30200 |NUM_ENCS, 2–49
30220, 4–90
30220 |ENC_MODULE_NR, 2–50
30230, 4–91
30230 |ENC_INPUT_NR, 2–50
30240, 4–91
30240 |ENC_TYPE, 2–50
30270 |ENC_ABS_BUFFERING, 2–50
30300, 4–91
30300 |IS_ROT_AX, 2–50
30310, 4–91
30310 |ROT_IS_MODULO, 2–50
30320, 4–92
30320 |DISPLAY_IS_MODULO, 2–50
30350, 4–92
30350 |SIMU_AX_VDI_OUTPUT, 2–50
30465 |AXIS_LANG_SUB_MASK, 2–50
305 |G_GROUP1, 2–25
30500 |INDEX_AX_ASSIGN_POS_TAB, 2–50
306 |G_GROUP2, 2–25
30600 |FIX_POINT_POS, 2–50
30600 , 4–92
307 |G_GROUP3, 2–25
308 |G_GROUP4, 2–25
309 |G_GROUP5, 2–25
310 |FG_GROUP1, 2–25
31000, 4–92
31000 |ENC_IS_LINEAR, 2–51
31010, 4–92
31010 |ENC_GRID_POINT_DIST, 2–51
31020, 4–92
31020 |ENC_RESOL, 2–51
31030, 4–93
31030 |LEADSCREW_PITCH, 2–51
31040, 4–93
SINUMERIK 802D sl Listas (LIS), Edición 02/2006
6FC5397–5CP10–0EA0
Índice de los datos de máquina/operador
31040 |ENC_IS_DIRECT, 2–51
31044 |ENC_IS_DIRECT2, 2–51
31050, 4–93
31050 |DRIVE_AX_RATIO_DENOM, 2–51
31060, 4–93
31060 |DRIVE_AX_RATIO_NUMERA, 2–51
31064 |DRIVE_AX_RATIO2_DENOM, 2–51
31066 |DRIVE_AX_RATIO2_NUMERA, 2–51
31070, 4–93
31070 |DRIVE_ENC_RATIO_DENOM, 2–51
31080, 4–93
31080 |DRIVE_ENC_RATIO_NUMERA, 2–51
311 |FG_GROUP2, 2–25
31122, 4–93
31122 |BERO_DELAY_TIME_PLUS, 2–51
31123, 4–93
31123 |BERO_DELAY_TIME_MINUS, 2–52
312 |FG_GROUP3, 2–25
313 |FG_GROUP4, 2–25
314 |FG_GROUP5, 2–25
32000, 4–94
32000 |MAX_AX_VELO, 2–52
32010, 4–94
32010 |JOG_VELO_RAPID, 2–52
32020, 4–94
32020 |JOG_VELO, 2–52
32100, 4–94
32100 |AX_MOTION_DIR, 2–52
32110, 4–95
32110 |ENC_FEEDBACK_POL, 2–52
32200, 4–95
32200 |POSCTRL_GAIN, 2–52
32210 |POSCTRL_INTEGR_TIME, 2–52
32220 |POSCTRL_INTEGR_ENABLE, 2–52
32230 |POSCTRL_CONFIG, 2–53
32300 |MAX_AX_ACCEL, 2–53
xi