Siemens SINUMERIK 802D sl Manual De Instrucciones página 7

Índice de los datos de máquina/operador
10000, 4–78
10000 |AXCONF_MACHAX_NAME_TAB, 2–29
10074, 4–78
10074 |PLC_IPO_TIME_RATIO, 2–29
10088 |REBOOT_DELAY_TIME, 2–29
10200 |INT_INCR_PER_MM, 2–29
10210 |INT_INCR_PER_DEG, 2–29
10240, 4–79
10240 |SCALING_SYSTEM_IS_METRIC, 2–29
10350 |FASTIO_DIG_NUM_INPUTS, 2–29
10360 |FASTIO_DIG_NUM_OUTPUTS, 2–29
10366 |HW_ASSIGN_DIG_FASTIN, 2–30
10368 |HW_ASSIGN_DIG_FASTOUT, 2–30
10450 |SW_CAM_ASSIGN_TAB, 2–30
10460 |SW_CAM_MINUS_LEAD_TIME, 2–30
10461 |SW_CAM_PLUS_LEAD_TIME, 2–30
10470 |SW_CAM_ASSIGN_FASTOUT_1, 2–30
10480 |SW_CAM_TIMER_FASTOUT_MASK, 2–30
10485 |SW_CAM_MODE, 2–30
10710 |PROG_SD_RESET_SAVE_TAB, 2–30
10713 |M_NO_FCT_STOPRE, 2–31
10714 |M_NO_FCT_EOP, 2–31
10715 |M_NO_FCT_CYCLE, 2–31
10716 |M_NO_FCT_CYCLE_NAME, 2–31
10717 |T_NO_FCT_CYCLE_NAME, 2–31
10718 |M_NO_FCT_CYCLE_PAR, 2–31
10719 |T_NO_FCT_CYCLE_MODE, 2–31
10735 |JOG_MODE_MASK, 2–31
10760 |G53_TOOLCORR, 2–31
10804 |EXTERN_M_NO_SET_INT, 2–31
10806 |EXTERN_M_NO_DISABLE_INT, 2–31
10808 |EXTERN_INTERRUPT_BITS_M96, 2–32
10810 |EXTERN_MEAS_G31_P_SIGNAL, 2–32
10812 |EXTERN_DOUBLE_TURRET_ON, 2–32
SINUMERIK 802D sl Listas (LIS), Edición 02/2006
6FC5397–5CP10–0EA0
Índice de los datos de máquina/operador
10814 |EXTERN_M_NO_MAC_CYCLE, 2–32
10815 |EXTERN_M_NO_MAC_CYCLE_NAME, 2–32
10816 |EXTERN_G_NO_MAC_CYCLE, 2–32
10817 |EXTERN_G_NO_MAC_CYCLE_NAME, 2–32
10818 |EXTERN_INTERRUPT_NUM_ASUP, 2–32
10820 |EXTERN_INTERRUPT_NUM_RETRAC, 2–33
10880 |MM_EXTERN_CNC_SYSTEM, 2–33
10881 |MM_EXTERN_GCODE_SYSTEM, 2–33
10882 |NC_USER_EXTERN_GCODES_TAB, 2–33
10884 |EXTERN_FLOATINGPOINT_PROG, 2–33
10886 |EXTERN_INCREMENT_SYSTEM, 2–33
10888 |EXTERN_DIGITS_TOOL_NO, 2–33
10890 |EXTERN_TOOLPROG_MODE, 2–33
10900 |INDEX_AX_LENGTH_POS_TAB_1, 2–33
10910 |INDEX_AX_POS_TAB_1, 2–33
10920 |INDEX_AX_LENGTH_POS_TAB_2, 2–34
10930 |INDEX_AX_POS_TAB_2, 2–34
11100, 4–79
11100 |AUXFU_MAXNUM_GROUP_ASSIGN, 2–34
11160 |ACCESS_EXEC_CST, 2–34
11161 |ACCESS_EXEC_CMA, 2–34
11162 |ACCESS_EXEC_CUS, 2–34
11165 |ACCESS_WRITE_CST, 2–34
11166 |ACCESS_WRITE_CMA, 2–34
11167 |ACCESS_WRITE_CUS, 2–34
11170 |ACCESS_WRITE_SACCESS, 2–34
11171 |ACCESS_WRITE_MACCESS, 2–34
11172 |ACCESS_WRITE_UACCESS, 2–35
11210, 4–79
11210 |UPLOAD_MD_CHANGES_ONLY, 2–35
11240, 4–80
11240 |PROFIBUS_SDB_NUMBER, 2–35
11250 |PROFIBUS_SHUTDOWN_TYPE, 2–35
11310, 4–80
vii