Siemens SINUMERIK 802D sl Manual De Instrucciones página 12

Índice de los datos de máquina/operador
32300 |MAX_AX_ACCEL, 4–95
32301 |JOG_MAX_ACCEL, 2–53
32320 |DYN_LIMIT_RESET_MASK, 2–53
32420 |JOG_AND_POS_JERK_ENABLE, 2–53
32420 |JOG_AND_POS_JERK_ENABLE, 4–95
32430 |JOG_AND_POS_MAX_JERK, 2–53
32430 |JOG_AND_POS_MAX_JERK, 4–96
32431, 4–96
32431 |MAX_AX_JERK, 2–53
32432, 4–96
32432 |PATH_TRANS_JERK_LIM, 2–53
32436 |JOG_MAX_JERK, 2–53
32440 |LOOKAH_FREQUENCY, 2–53
32450, 4–96
32450 |BACKLASH, 2–53
32490 |FRICT_COMP_MODE, 2–54
32500 |FRICT_COMP_ENABLE, 2–54
32510 |FRICT_COMP_ADAPT_ENABLE, 2–54
32520 |FRICT_COMP_CONST_MAX, 2–54
32530 |FRICT_COMP_CONST_MIN, 2–54
32540 |FRICT_COMP_TIME, 2–54
32610 |VELO_FFW_WEIGHT, 2–54
32630, 4–96
32630 |FFW_ACTIVATION_MODE, 2–54
32640 |STIFFNESS_CONTROL_ENABLE, 2–54
32642 |STIFFNESS_CONTROL_CONFIG, 2–54
32644 |STIFFNESS_DELAY_TIME, 2–54
32700, 4–97
32700 |ENC_COMP_ENABLE, 2–55
32810, 4–97
32810 |EQUIV_SPEEDCTRL_TIME, 2–55
330 |CMM_POS_COORDINATE_SYSTEM, 2–26
33050, 4–97
33050 |LUBRICATION_DIST, 2–55
331 |CONTOUR_MASK, 2–26
332 |TOOL_LIST_PLACE_NO, 2–26
xii
34000, 4–97
34000 |REFP_CAM_IS_ACTIVE, 2–55
34010, 4–97
34010 |REFP_CAM_DIR_IS_MINUS, 2–55
34020, 4–98
34020 |REFP_VELO_SEARCH_CAM, 2–55
34030, 4–98
34030 |REFP_MAX_CAM_DIST, 2–55
34040, 4–98
34040 |REFP_VELO_SEARCH_MARKER, 2–55
34050, 4–98
34050 |REFP_SEARCH_MARKER_REVERSE, 2–55
34060, 4–99
34060 |REFP_MAX_MARKER_DIST, 2–55
34070, 4–99
34070 |REFP_VELO_POS, 2–56
34080, 4–99
34080 |REFP_MOVE_DIST, 2–56
34090, 4–99
34090 |REFP_MOVE_DIST_CORR, 2–56
34092, 4–100
34092 |REFP_CAM_SHIFT, 2–56
34093, 4–100
34093 |REFP_CAM_MARKER_DIST, 2–56
34100, 4–100
34100 |REFP_SET_POS, 2–56
34110, 4–101
34110 |REFP_CYCLE_NR, 2–56
34120 |REFP_BERO_LOW_ACTIVE, 2–56
34200, 4–101
34200 |ENC_REFP_MODE, 2–56
34210 |ENC_REFP_STATE, 2–56
34210 , 4–102
34220 |ENC_ABS_TURNS_MODULO, 2–57
34220 , 4–102
343 |V24_PPI_ADDR_MMC, 2–26
SINUMERIK 802D sl Listas (LIS), Edición 02/2006
6FC5397–5CP10–0EA0