Siemens SINUMERIK 802D sl Manual De Instrucciones página 13

344 |V24_PPI_MODEM_ACTIVE, 2–26
345 |V24_PPI_MODEM_BAUD, 2–26
346 |V24_PPI_MODEM_PARITY, 2–26
34990 |ENC_ACTVAL_SMOOTH_TIME, 2–57
35000, 4–103
35000 |SPIND_ASSIGN_TO_MACHAX, 2–57
35010, 4–103
35010 |GEAR_STEP_CHANGE_ENABLE, 2–57
35012 |GEAR_STEP_CHANGE_POSITION, 2–57
35014 |GEAR_STEP_USED_IN_AXISMODE, 2–57
35020 |SPIND_DEFAULT_MODE, 2–57
35030 |SPIND_DEFAULT_ACT_MASK, 2–57
35040, 4–103
35040 |SPIND_ACTIVE_AFTER_RESET, 2–57
35100, 4–104
35100 |SPIND_VELO_LIMIT, 2–57
35110, 4–104
35110 |GEAR_STEP_MAX_VELO, 2–57
35112 |GEAR_STEP_MAX_VELO2, 2–57
35120, 4–104
35120 |GEAR_STEP_MIN_VELO, 2–58
35122 |GEAR_STEP_MIN_VELO2, 2–58
35130, 4–105
35130 |GEAR_STEP_MAX_VELO_LIMIT, 2–58
35140, 4–105
35140 |GEAR_STEP_MIN_VELO_LIMIT, 2–58
35150, 4–106
35150 |SPIND_DES_VELO_TOL, 2–58
35160, 4–106
35160 |SPIND_EXTERN_VELO_LIMIT, 2–58
35200, 4–106
35200 |GEAR_STEP_SPEEDCTRL_ACCEL, 2–58
35210, 4–106
35210 |GEAR_STEP_POSCTRL_ACCEL, 2–58
35212 |GEAR_STEP_POSCTRL_ACCEL2, 2–58
35300, 4–107
SINUMERIK 802D sl Listas (LIS), Edición 02/2006
6FC5397–5CP10–0EA0
Índice de los datos de máquina/operador
35300 |SPIND_POSCTRL_VELO, 2–58
35310, 4–107
35310 |SPIND_POSIT_DELAY_TIME, 2–58
35350, 4–107
35350 |SPIND_POSITIONING_DIR, 2–59
35400, 4–107
35400 |SPIND_OSCILL_DES_VELO, 2–59
35410, 4–107
35410 |SPIND_OSCILL_ACCEL, 2–59
35430, 4–108
35430 |SPIND_OSCILL_START_DI, 2–59
35440, 4–108
35440 |SPIND_OSCILL_TIME_CW, 2–59
35450, 4–108
35450 |SPIND_OSCILL_TIME_CCW, 2–59
35500, 4–109
35500 |SPIND_ON_SPEED_AT_IPO_START, 2–59
35510, 4–109
35510 |SPIND_STOPPED_AT_IPO_START, 2–59
35550 |DRILL_VELO_LIMIT, 2–59
356 |HMI_COL_TITLE_FOCUS_FORE, 2–26
357 |HMI_COL_TITLE_FOCUS_BACK, 2–26
360 |SPINDLE_LOAD_DISPL1, 2–26
36000 |STOP_LIMIT_COARSE, 2–59 , 4–109
36010, 4–110
36010 |STOP_LIMIT_FINE, 2–59
36020 |POSITIONING_TIME, 2–59 , 4–110
36030 |STANDSTILL_POS_TOL, 2–60 , 4–110
36040 |STANDSTILL_DELAY_TIME, 2–60 , 4–110
36050, 4–110
36050 |CLAMP_POS_TOL, 2–60
36060, 4–111
36060 |STANDSTILL_VELO_TOL, 2–60
361, 4–76
361 |USER_MEAS_TOOL_CHANGE, 2–26
36100 |POS_LIMIT_MINUS, 2–60 , 4–111
xiii