Publicidad
Idiomas disponibles
Idiomas disponibles
6. INFORMATION ON HOW TO USE THE MACHINE
6.1 Introduction
Reference should be made to the contents of section relating to the correct use of the machine.
4. INSTALLATION AND START-UP OF THE MACHINE
6. INFORMATION ON HOW TO USE THE MACHINE
6.2 Preparing the machine to be used
To obtain the dough, follow the instructions below:
4.1 Setting up the machine
6.1 Introduction
- lift the mobile guard as far as possible;
Position the machine in a place suitable for its intended use which complies with all mandatory
Reference should be made to the contents of section relating to the correct use of the machine.
- add the recipe ingredients to the maximum quantity of the dough capacity indicated in the table in
safety conditions. The area must be equipped with sufficient lighting and aeration.
section 5.1 (Description of machine operating functions).
Position the machine observing the minimum distances from walls, as illustrated in fig. 5, to ensure
Abide by the maximum dough consistence limit, as indicated in section 2.1 (Correct use and features).
6.2 Preparing the machine to be used
there is sufficient space for work, cleaning and routine maintenance operations. This will also allow
The flour should be added in a way that produces as little dust as possible, as inhalation of flour can be
operators to work in safe conditions, avoiding any crushing and/or being dragged between the bowl
To obtain the dough, follow the instructions below:
a health hazard and cause rhinitis, watery eyes and, in more serious cases, asthma.
and the wall. When positioned as above, the machine is stable and does not require anchoring to the
- lift the mobile guard as far as possible;
- lower the mobile guard.
floor.
- add the recipe ingredients to the maximum quantity of the dough capacity indicated in the table in
section 5.1 (Description of machine operating functions).
6.3 Processing
100 cm
10 cm
Abide by the maximum dough consistence limit, as indicated in section 2.1 (Correct use and features).
To start the machine, connect it to the mains, lower the guard disengage the emergency button
The flour should be added in a way that produces as little dust as possible, as inhalation of flour can be
and press the start button.
a health hazard and cause rhinitis, watery eyes and, in more serious cases, asthma.
The machine will then perform the required processing operation; the machine will stop when the
- lower the mobile guard.
dough is ready. This operation can also be performed by pressing the emergency button or by lifting
the bowl guard (even when the machine is running).
6.3 Processing
To manually inspect the dough or add ingredients, it is recommended to use the dedicated opening
To start the machine, connect it to the mains, lower the guard disengage the emergency button
on the guard.
and press the start button.
The machine will then perform the required processing operation; the machine will stop when the
6.4 Removing the dough
dough is ready. This operation can also be performed by pressing the emergency button or by lifting
The dough is removed from the bowl by hand, in portions, with or without the help of a knife.
the bowl guard (even when the machine is running).
To manually inspect the dough or add ingredients, it is recommended to use the dedicated opening
on the guard.
6.4 Removing the dough
The dough is removed from the bowl by hand, in portions, with or without the help of a knife.
4.2 Electrical power supply
The machine is equipped with one single electrical connection with a power cord at the back of the
6.5 Switching off the machine
machine; the system layout can be seen in the diagram supplied with the machine.
The tool and bowl rotation motor can be interrupted at any moment in time by pressing the
Check that the rated plate voltage corresponds to the main network voltage and the rated plate
emergency button; the machine will also stop when the power is disconnected; when the start
power is equal or lower than the network power.
button is pressed again, the cycle will continue from the point in which it was interrupted, after the
The connection must foresee coupling to a manual voltage disconnection switch, to allow the
emergency button has been released.
separation of the electric machine parts from the mains network when necessary (e.g. during
6.5 Switching off the machine
cleaning or maintenance). This device serves to transmit the correct rated current; the diameter of
the main network connection and external protection (earthing) cables must be proportional and
The tool and bowl rotation motor can be interrupted at any moment in time by pressing the
adequate for the rated current.
emergency button; the machine will also stop when the power is disconnected; when the start
Attach a retention plug to the end of the machine power cord suitable for the disconnection switch
button is pressed again, the cycle will continue from the point in which it was interrupted, after the
installed and plug it into the socket.
emergency button has been released.
Start the machine and check that the spiral mixer turns in the direction indicated by the arrow on the
40
front of the structure below the bowl. If this is not the case, invert the position of the two phase wires
in the plug. The machine does not require any other type of intervention and is now ready to use.
40
35
29
Publicidad
