Publicidad
Idiomas disponibles
Idiomas disponibles
EN
Function
Default
N.
O.
P.
R.
T.
U.
V.
Y.
* After modifying the "Motion direction" parameter, the subsequent
first opening and closing operations will be carried out at reduced
speed.
12.2 - Obstacle detection
If the door encounters an obstacle during closing, it reopens
immediately, remains open for the pause time and then closes
again. Subsequent closure takes place slowing down near the point
where the obstacle was detected. If the obstacle is encountered
three consecutive times, the door remains stationary, pressing
12.3 - Monitored safety devices
Monitored safety devices, equipped with a stimulation input, can
be connected to the STOP, PHOTO and PHOTO RALL inputs.
An unattended device or a monitored device or a series of two
monitored devices can be connected to each of the three inputs. It
is necessary to set the configuration of each individual input using
parameters L, N and O (see Modification of parameters). In the
case of the unattended device, the corresponding parameter must
be set to the value 0. In this case, no device test is performed.
In the case of a single monitored device, the corresponding
parameter must be set to 1. In this case, the device test is carried
out via the TEST 1 output, which connects to the test input of the
monitored device. In the case of two monitored devices connected
in series, the corresponding parameter must be set to the value
2. In this case, testing of the first device is carried out through
12.4 - Settings with special CODES
With the equipment off (without power) press the OK button and
keep it pressed, at this point turn on the equipment (activate
power), keeping the ok button pressed and after a few seconds
the equipment emits a short acoustic signal. At this point, release
the OK key, and the display will show: "
Using the P1 and P2 keys it is possible to modify the first two digits
and the second two digits of the number separately, thus setting
a special configuration code, which must then be confirmed by
pressing the OK key for two seconds.
Depending on the special code set, the following operations will
be performed:
74
Min
Max
0
0
2
0
0
2
0
0
1
0
0
1
0
0
1
0
0
9
0
0
9
0
0
2
0000
".
Value
SLOW. PHOTO monitoring
STOP monitoring
Battery presence
Lock if R.INT or R.EXT
Radar Type
START opening duration
Lock delay
Interlock
ATTENTION !
The values may vary according to the weight class of the door.
against it.
If the door encounters an obstacle during opening, it locks and
remains stationary for the set pause time, then closes at reduced
speed. Subsequent opening takes place slowing down near the
point where the obstacle was detected.
the TEST 1 output, which connects to the test input of the first
monitored device, and the test of the second device is performed
through the TEST 2 output, which connects to the test input of the
second monitored device. The tests are carried out immediately
after the end of each door opening movement; if one of the tests
fails, the corresponding error is displayed (see Errors) and the
door does not close. Every 30 seconds the test is repeated (in the
case of opening with the OPEN command, the test is repeated
upon receipt of the CLOSE command), and if it succeeds the door
closes again. During this error state, it is still possible to move
the selector to the Lock position and close the door by hand: two
seconds after closing, the electric lock will be activated.
password 4444: A4 new KEY motor
password 2468: Start cyclic test mode
password 1234: Enabling of special displays
password 3223: Reset parameters from 1 to 8 as per
password 9696: Restart of all parameters as
password 8585: NT.I emergency closure (N.C.). With this
at the value 3. It can then be changed from the
keypad but not shown with value 3
Notes
0 = not monitored
1 = a monitored device
2 = two monitored devices
0 = not monitored
1 = a monitored device
2 = two monitored devices
0 = battery not present
1 = battery present
0 = Normal operation
1 = RINT or REXT lock closed door
0 = normal radar
1 = 100Hz output Hotron radar
0 = step-step
from 1 to 9 (in tenths of seconds)
from 0 to 9 (in tenths of seconds)
0 = disabled
1 = enabled
2 = emergency opening
default according to the door weight class
default settings. After the
restart, a learning is forced
password the Y parameters is set
Publicidad
