Publicidad
Idiomas disponibles
Idiomas disponibles
Tuner Setup
Tuner Setup
Setting up TV channels
This section describes how to search and set up TV channels
that you can watch under the current conditions. Unless you
set up TV channels using Auto Channel Preset, you may not be
able to tune in those channels.
Using Auto Channel Preset
Auto Channel Preset automatically searches and sets up TV
channels.
1
Press HOME MENU.
2
Select "Tuner Setup". ( /
3
Select "Channel Setup". ( /
4
Select "Ant. A" or "Ant. B". ( /
5
Select "Auto Channel Preset". ( /
6
Select "Air" or "Cable". ( /
Channel Setup
Ant. A
Auto Ch. Preset
Ant. A
Auto Channel Preset
Enter
Begin Preset
• Channel search automatically starts.
Channel Setup
Ant. A
Auto Ch. Preset
Ant. A
Auto Channel Preset
• Cable
D
Cancel
• To quit Auto Channel Preset halfway, press D.
7
After Auto Channel Preset has been finished, press HOME
MENU to exit the menu.
NOTE
• When using the Cable Converter, you may need to manually
add Cable Converter output channels.
• When an inserted CableCARD™ is functioning, you can
execute Auto Channel Preset by selecting "Ant.B" in step 4.
Setting for skipping unwanted channels
From among TV channels searched and set up using Auto
Channel Preset, you can select channels to be skipped when
CH+/- are operated.
1
Press HOME MENU.
2
Select "Tuner Setup". ( /
3
Select "Channel Setup". ( /
4
Select "Ant. A" or "Ant. B". ( /
5
Select "Channel Keep/Skip". ( /
6
Select a channel to be skipped. ( /
Channel Setup Ant. A
Ant. A
Channel Keep/Skip
then ENTER)
then ENTER)
then ENTER)
then ENTER)
then ENTER)
Cable
xxxxxxxxxxxxxxxxxxxxx
Air
2.0
xxxxxxxxxxxxxxxxxxxxx
Cable
4.0
xxxxxxxxxxxxxxxxxxxxx
6.0
D
Cancel
Home Menu
Exit
Cable
xxxxxxxxxxxxxxxx
One Moment Please ...
xxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxx
Home Menu
Exit
then ENTER)
then ENTER)
then ENTER)
then ENTER)
then ENTER)
Channel Keep/Skip
xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
2.0
xxxxxxxxxxxxxxxxxxxxx
4.0
6.0
Exit
Home Menu
• For the skipped channel, a check mark disappears.
7
Press HOME MENU to exit the menu.
NOTE
• To restore skipped channels, use the above procedure
except that you select a skipped channel in step 6.
• When using the Cable Converter, you may need to manually
add Cable Converter output channels.
Setting up TV channels manually
This section describes how to manually set up TV channels that
have not been set up by Auto Channel Preset.
1
Press HOME MENU.
2
Select "Tuner Setup". ( /
3
Select "Channel Setup". ( /
4
Select "Ant. A" or "Ant. B". ( /
5
Select "Add Channel". ( /
6
Select a channel number to be added. ( /
• You can also use buttons 0 – 9 to enter a channel
number.
Channel Setup Ant. A
Add Channel
Ant. A
Add Channel
• After ENTER has been pressed, a confirmation screen
appears.
7
Press A to complete the setup process.
8
Press HOME MENU to exit the menu.
NOTE
• Adding channels manually is for adding analog channels
only. Digital channels cannot be added.
Checking signal strength
When you have selected antenna A, you can check the current
channel's signal strength. You may use this function when
receiving a channel through a VHF/UHF antenna.
1
Press HOME MENU.
2
Select "Tuner Setup". ( /
3
Select "Channel Setup". ( /
4
then ENTER)
Select "Ant. A". ( /
5
Select "Signal Strength". ( /
Channel Setup
Ant. A
Signal Strength
Maximum: 100
Current: 100
Ant. A
Signal Strength
• Adjust the direction of the antenna so that the current
signal strength reaches as close to the maximum signal
strength as possible.
6
Press HOME MENU to exit the menu.
then ENTER)
then ENTER)
then ENTER)
then ENTER)
then ENTER)
xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
000
1
xxxxxxxxxxxxxxxxxxxxx
Home Menu
Exit
then ENTER)
then ENTER)
then ENTER)
xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
Home Menu
Exit
09
43
En
Publicidad
