Publicidad
The fixing screw must be fixed firmly.
CARBEST VanVent | 318028/318029
4.Remove the upper part of the PLUS FAN top cover, align it with the body fixing plate
frame, and insert the upper part into the frame. After pressing, apply an appropriate
amount of sealant (recommended to use MS type sealant) to (PT4.0 × 12 (4)), and then
use screws to fix the upper part of the body fixing plate.
Mounting of PLUS Fan
5.Arrange the outgoing wires of the upper assembly of the top cover of PLUS FAN . There
are altogether 3 kinds of wiring terminals (1#/2#/3#female ends).
The side fixing screws must be fixed after tightening; otherwise there will be a gap between
the adhesive tape between the upper assembly and the body fixing plate, probably causing
water leakage. (Recommended screw torque: 0.7 N.m)
The side fixing screws must be fixed after tightening;
otherwise there will be a gap between the adhesive tape
14
between the outdoor unit and the mounting frame, proba-
bly causing water leakage. (Recommended screw torque:
Mounting of PLUS Fan
0.7 N.m)
5.Arrange the outgoing wires of the upper assembly of the top cover of PLUS FAN . There
are altogether 3 kinds of wiring terminals (1#/2#/3#female ends).
Fan motor wire: (Green, blue and yellow) 3P male end 1#;
Lifting motor wire: (Red and black) 2P male terminal 2 #,
(green, orange and yellow) 3P male terminal 3 #;
Vehicle power cord: (Red and black) bare wire;
6.Arrange the outgoing wires of the lower assembly of the interior trim frame of PLUS
Fan motor wire: (Green, blue and yellow) 3P male end 1#;
FAN , and respectively use 3 kinds of wiring terminals (1#/2#/3#male ends).
Lifting motor wire: (Red and black) 2P male terminal 2 #,
(green, orange and yellow) 3P male terminal 3 #;
Vehicle power cord: (Red and black) bare wire;
6.Arrange the outgoing wires of the lower assembly of the interior trim frame of PLUS
FAN , and respectively use 3 kinds of wiring terminals (1#/2#/3#male ends).
Fan motor wire: (Green, blue and yellow) 3P female end 1#;
The harness shall be clean, and free from damage and
Fan motor wire: (Green, blue and yellow) 3P female end 1#;
Lifting motor wire: (Red and black) 2P female terminal 2#,
Lifting motor wire: (Red and black) 2P female terminal 2#,
winding. The terminals shall be firmly connected and the
(green, orange and yellow) 3P female terminal 3#;
(green, orange and yellow) 3P female terminal 3#;
Input power wire of ventilating fan: (Red and black) bare wire;
pins shall be free from any damage.
Input power wire of ventilating fan: (Red and black) bare wire;
The harness shall be clean, and free from damage and winding. The terminals shall be firmly
connected and the pins shall be free from any damage.
The harness shall be clean, and free from damage and winding. The terminals shall be firmly
connected and the pins shall be free from any damage.
1
2 12 V
21
4.
Place the VanVent outdoor
unit on the mounting frame.
After pressing in, apply an
appropriate amount of sealant
(DEKAseal 8936 recommend-
ed) to the screw holes and
use screws (PT4.0x12 (4)) to
connect the two parts.
5.
1 VanVent have 3 types of
connectors:
Fan motor wire:
- (Green, blue and yellow)
Lifting motor wire:
- (Red and black)
- (Green, orange and yellow)
2 Vehicle power cord 12V
(Red and black) bare wire;
15
15
DE
EN
IT
ES
FR
NL
FI
DK
SE
Publicidad
