Publicidad
Harness shall be neat and all terminals shall be connected firmly without insufficient or
omitted connection. Screws shall be fixed firmly.
CARBEST VanVent | 318028/318029
10.Insert the lamp covers laterally into the corresponding slots in the lower assembly of
the PLUS FAN trim frame.
ounting of PLUS FAN
Mounting of PLUS FAN
After completing the above steps, clean the debris and dust on the PLUS FAN casing.
ss the power button on the control panel to start using the device.
11.After completing the above steps, clean the debris and dust on the PLUS FAN casing.
Press the power button on the control panel to start using the device.
Mounting of PLUS FAN
Upon inserting, the lampshade will emit three clicks, indicating that the lampshade has
been clamped in place.
Al momento dell'inserimento, il paralume emette tre scat-
11.After completing the above steps, clean the debris and dust on the PLUS FAN casing.
ti, a indicare che il paralume è stato bloccato in posizione.
Press the power button on the control panel to start using the device.
After powering on the device for the very first time, try each button on the control
el three times to check the functions of button backlight, lighting lamp, fan
12.After powering on the device for the very first time, try each button on the control
panel three times to check the functions of button backlight, lighting lamp, fan
eleration, fan deceleration, open top cover, close top cover, etc.
acceleration, fan deceleration, open top cover, close top cover, etc.
Take the remote control base and 2 ST3.5×13 cross pan-head screws, tear off the
uble-sided adhesive tape on the back of the remote control base, stick it in the
13.Take the remote control base and 2 ST3.5×13 cross pan-head screws, tear off the
double-sided adhesive tape on the back of the remote control base, stick it in the
determined position and fix it with screws.
predetermined position and fix it with screws.
12.After powering on the device for the very first time, try each button on the control
Mount a total of 2 AA batteries in the remote control,
which can be used after the code is successfully matched.
Mount a total of 2 AA batteries in the remote control,
panel three times to check the functions of button backlight, lighting lamp, fan
which can be used after the code is successfully matched.
acceleration, fan deceleration, open top cover, close top cover, etc.
Please insert the remote control into the base of the
remote control when it is not used.
Please insert the remote control into the base of the
13.Take the remote control base and 2 ST3.5×13 cross pan-head screws, tear off the
remote control when it is not used.
double-sided adhesive tape on the back of the remote control base, stick it in the
predetermined position and fix it with screws.
Mount a total of 2 AA batteries in the remote control,
which can be used after the code is successfully matched.
Please insert the remote control into the base of the
remote control when it is not used.
2x ST3.5x13
L'accoppiamento deve essere completato entro 20 s
The code matching must be completed within 20 s after the ventilation fan is powered on
(otherwise, cut off the power supply and re-match).
The code matching must be completed within 20 s after the ventilation fan is powered on
dall'accensione del ventilatore (altrimenti, interrompere
(otherwise, cut off the power supply and re-match).
l'alimentazione e ripetere l'accoppiamento).
18
The code matching must be completed within 20 s after the ventilation fan is powered on
(otherwise, cut off the power supply and re-match).
18
ON/OFF
LAMP
IN/OUT
SLOW
AUTO
FAST
ON/OFF
LAMP
IN/OUT
SLOW
AUTO
FAST
ON/OFF
IN/OUT
SLOW
AUTO
FAST
LAMP
33
9.
Inserire i coperchi delle lam-
pade nelle fessure corrispond-
enti dell'unità interna
17
10.
Pronto per l'uso
11.
Montare un totale di 2 bat-
terie AA (non incluse) nel
telecomando, che può essere
utilizzato dopo aver effettuato
con successo l'accoppiamento
con VanVent. Utilizzare le viti
ST3,5x13 (2 pezzi) per mon-
tare la base del telecomando
alla parete.
Quando non viene utilizzato,
inserire il telecomando nella
sua base.
DE
EN
IT
ES
FR
NL
FI
DK
SE
Publicidad
