Publicidad
Harness shall be neat and all terminals shall be connected firmly without insufficient or
omitted connection. Screws shall be fixed firmly.
CARBEST VanVent | 318028/318029
10.Insert the lamp covers laterally into the corresponding slots in the lower assembly of
the PLUS FAN trim frame.
ounting of PLUS FAN
Mounting of PLUS FAN
After completing the above steps, clean the debris and dust on the PLUS FAN casing.
ss the power button on the control panel to start using the device.
11.After completing the above steps, clean the debris and dust on the PLUS FAN casing.
Press the power button on the control panel to start using the device.
Mounting of PLUS FAN
Upon inserting, the lampshade will emit three clicks, indicating that the lampshade has
Når lampeskærmen sættes i, udsender den tre klik, hvilket
been clamped in place.
11.After completing the above steps, clean the debris and dust on the PLUS FAN casing.
indikerer, at lampeskærmen er klemt på plads.
Press the power button on the control panel to start using the device.
After powering on the device for the very first time, try each button on the control
el three times to check the functions of button backlight, lighting lamp, fan
12.After powering on the device for the very first time, try each button on the control
panel three times to check the functions of button backlight, lighting lamp, fan
eleration, fan deceleration, open top cover, close top cover, etc.
acceleration, fan deceleration, open top cover, close top cover, etc.
Take the remote control base and 2 ST3.5×13 cross pan-head screws, tear off the
uble-sided adhesive tape on the back of the remote control base, stick it in the
13.Take the remote control base and 2 ST3.5×13 cross pan-head screws, tear off the
double-sided adhesive tape on the back of the remote control base, stick it in the
determined position and fix it with screws.
predetermined position and fix it with screws.
12.After powering on the device for the very first time, try each button on the control
Mount a total of 2 AA batteries in the remote control,
which can be used after the code is successfully matched.
Mount a total of 2 AA batteries in the remote control,
panel three times to check the functions of button backlight, lighting lamp, fan
which can be used after the code is successfully matched.
acceleration, fan deceleration, open top cover, close top cover, etc.
Please insert the remote control into the base of the
remote control when it is not used.
Please insert the remote control into the base of the
13.Take the remote control base and 2 ST3.5×13 cross pan-head screws, tear off the
remote control when it is not used.
double-sided adhesive tape on the back of the remote control base, stick it in the
predetermined position and fix it with screws.
Mount a total of 2 AA batteries in the remote control,
which can be used after the code is successfully matched.
Please insert the remote control into the base of the
remote control when it is not used.
2x ST3.5x13
The code matching must be completed within 20 s after the ventilation fan is powered on
Parringen skal være afsluttet inden for 20 sekunder, efter
(otherwise, cut off the power supply and re-match).
The code matching must be completed within 20 s after the ventilation fan is powered on
at ventilatoren er tændt (ellers skal du afbryde strømforsy-
(otherwise, cut off the power supply and re-match).
ningen og parre igen).
18
The code matching must be completed within 20 s after the ventilation fan is powered on
(otherwise, cut off the power supply and re-match).
18
ON/OFF
LAMP
IN/OUT
SLOW
AUTO
FAST
ON/OFF
LAMP
IN/OUT
SLOW
AUTO
FAST
ON/OFF
IN/OUT
SLOW
AUTO
FAST
LAMP
83
9.
Indsæt lampedækslerne i
de tilsvarende åbninger i
indendørsenheden
17
10.
Klar til brug
11.
Monter i alt 2 AA-batterier
(medfølger ikke) i fjernbetje-
ningen, som kan bruges efter
vellykket parring med VanVent.
Brug skruerne ST3,5x13 (2
stk.) til at montere fjernbetje-
ningens base på væggen.
Sæt venligst fjernbetjeningen
ind i fjernbetjeningens base,
når den ikke bruges.
DE
EN
IT
ES
FR
NL
FI
DK
SE
Publicidad
