Publicidad
The fixing screw must be fixed firmly.
CARBEST VanVent | 318028/318029
4.Remove the upper part of the PLUS FAN top cover, align it with the body fixing plate
frame, and insert the upper part into the frame. After pressing, apply an appropriate
amount of sealant (recommended to use MS type sealant) to (PT4.0 × 12 (4)), and then
use screws to fix the upper part of the body fixing plate.
Mounting of PLUS Fan
5.Arrange the outgoing wires of the upper assembly of the top cover of PLUS FAN . There
are altogether 3 kinds of wiring terminals (1#/2#/3#female ends).
The side fixing screws must be fixed after tightening; otherwise there will be a gap between
the adhesive tape between the upper assembly and the body fixing plate, probably causing
Fastgørelsesskruerne på siden skal fastgøres efter til-
water leakage. (Recommended screw torque: 0.7 N.m)
spænding; ellers vil der være et hul mellem klæbebåndet
14
mellem udendørsenheden og monteringsrammen, hvilket
sandsynligvis vil forårsage vandlækage. (Anbefalet skrue-
Mounting of PLUS Fan
moment: 0,7 N.m)
5.Arrange the outgoing wires of the upper assembly of the top cover of PLUS FAN . There
are altogether 3 kinds of wiring terminals (1#/2#/3#female ends).
Fan motor wire: (Green, blue and yellow) 3P male end 1#;
Lifting motor wire: (Red and black) 2P male terminal 2 #,
(green, orange and yellow) 3P male terminal 3 #;
Vehicle power cord: (Red and black) bare wire;
6.Arrange the outgoing wires of the lower assembly of the interior trim frame of PLUS
FAN , and respectively use 3 kinds of wiring terminals (1#/2#/3#male ends).
Fan motor wire: (Green, blue and yellow) 3P male end 1#;
Lifting motor wire: (Red and black) 2P male terminal 2 #,
(green, orange and yellow) 3P male terminal 3 #;
Vehicle power cord: (Red and black) bare wire;
6.Arrange the outgoing wires of the lower assembly of the interior trim frame of PLUS
FAN , and respectively use 3 kinds of wiring terminals (1#/2#/3#male ends).
Fan motor wire: (Green, blue and yellow) 3P female end 1#;
Lifting motor wire: (Red and black) 2P female terminal 2#,
Ledningsnettet skal være rent og fri for skader og viklinger.
Fan motor wire: (Green, blue and yellow) 3P female end 1#;
(green, orange and yellow) 3P female terminal 3#;
Lifting motor wire: (Red and black) 2P female terminal 2#,
Klemmerne skal være solidt forbundet, og stifterne skal
(green, orange and yellow) 3P female terminal 3#;
Input power wire of ventilating fan: (Red and black) bare wire;
være fri for skader.
Input power wire of ventilating fan: (Red and black) bare wire;
The harness shall be clean, and free from damage and winding. The terminals shall be firmly
The harness shall be clean, and free from damage and winding. The terminals shall be firmly
connected and the pins shall be free from any damage.
connected and the pins shall be free from any damage.
1
2 12 V
81
4.
Placer VanVent udendørsen-
heden på monteringsrammen.
Når du har trykket den ind,
skal du påføre en passende
mængde fugemasse (DEKAseal
8936 anbefales) på skrue-
hullerne og bruge skruer
(PT4.0x12 (4)) til at forbinde de
to dele.
5.
1 VanVent har 3 typer af stik:
Ledning til blæsermotor:
- (grøn, blå og gul)
Ledning til løftemotor:
- (rød og sort)
- (Grøn, orange og gul)
2 Køretøjets strømkabel 12 V
(rød og sort) uden ledning;
15
15
DE
EN
IT
ES
FR
NL
FI
DK
SE
Publicidad
