Publicidad
Mounting of PLUS FAN
Mounting of PLUS FAN
7. INSTALLATION AV VANVENT
DE
1.Open mounting holes for the PLUS FAN on the roof (strong wall with a width ≥30mm is
OBS!
Vi rekommenderar att installationen utförs av kvalificerad personal. Be din
required around the hole to ensure that the self-tap screw can be firmly nailed into that
1.Open mounting holes for the PLUS FAN on the roof (strong wall with a width ≥30mm is
wall) according to the hole size drawing on the [Mounting Dimensions] page. Power cord
required around the hole to ensure that the self-tap screw can be firmly nailed into that
återförsäljare att installera VanVent om du inte har tillräcklig kunskap om installation.
EN
wall) according to the hole size drawing on the [Mounting Dimensions] page. Power cord
≥50mm can be optionally reserved in the opening on the left or right side of the body.
≥50mm can be optionally reserved in the opening on the left or right side of the body.
IT
ES
R5
R5
FR
NL
The outlet on the left side of the vehicle body is taken as an example in this manual.
The outlet on the left side of the vehicle body is taken as an example in this manual.
FI
Uttaget på vänster sida av fordonskorgen används som
2.Take out the vehicle body fixing plate from the package, and inject sealant (MS type
2.Take out the vehicle body fixing plate from the package, and inject sealant (MS type
exempel i denna manual.
sealant recommended) into the rubber groove of the outer ring of the vehicle body
sealant recommended) into the rubber groove of the outer ring of the vehicle body
DK
fixing plate frame. The sealant should not be too much, and any excessive glue should
fixing plate frame. The sealant should not be too much, and any excessive glue should
be cleaned up with a soft scraper.
be cleaned up with a soft scraper.
SE
Mounting of PLUS FAN
Mängden tätningsmedel ska vara jämn. Applicera inte för
The amount of glue should be even. Do not apply too much glue.
mycket tätningsmedel.
3.Fix the body fixing plate on the wall of the motor home with ST4.2×25 cross pan-head
The amount of glue should be even. Do not apply too much glue.
screws (16 pcs) outside the body. After fixing the screws, remove excessive glue around
the body fixing plate, if any.
The fixing screw must be fixed firmly.
Fästskruven måste vara ordentligt åtdragen.
4.Remove the upper part of the PLUS FAN top cover, align it with the body fixing plate
frame, and insert the upper part into the frame. After pressing, apply an appropriate
amount of sealant (recommended to use MS type sealant) to (PT4.0 × 12 (4)), and then
use screws to fix the upper part of the body fixing plate.
12 V
90
CARBEST VanVent | 318028/318029
1.
Före installation, kontrollera
takets tjocklek, som bör vara
mellan 27 mm och 80 mm.
Markera utskärningsöppningen
(400x400 mm) på taket och
skär ut hålet i taket.
12 V nätsladd ( >=50 mm) från
fordonsbatteriet kan förvaras
i öppningen på vänster eller
höger sida.
2.
Innan VanVent installeras
måste ytan rengöras (fri från
damm och fett). Applicera en
tillräcklig mängd av lämpligt
lim (rekommenderat DEKAseal
8936) runt kanten på monter-
ingsramen.
13
3.
13
Fäst monteringsramen på
fordonets tak med ST4.2x25
kryssskruvar (16 st.).
Ta bort överflödigt lim.
Publicidad
