Publicidad
Idiomas disponibles
Idiomas disponibles
TROUBLESHOOTING
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component,
check the points below. Sometimes the trouble may lie in another component.
Investigate the other components and electrical
appliances being used.
If the trouble cannot be rectified even after exercising the checks listed below, ask your nearest PIONEER authorized service center or
your dealer to carry out repair work.
eAC cord is unplugged.
e@All cords are not connected firmly.
@Plug power cord into wall socket correctly.
eConnect
cords
correctly
referring
to
"CONNECTIONS", see page 10.
@ Select the correct function.
Plug in the power cord.
e@ Use a cassette tape that can be recorded on, or
apply adhesive tape over tab holes.
Sound is muffled. Previously | e Dirty heads.
eClean heads, see page 64.
recorded sounds remain.
Sound
is muffled.
Treble
| e Tape recorded with DOLBY NR but played | eTurn on DOLBY NR system for tapes recorded
tones too strong.
without.
with DOLBY NR.
High-range sounds are over- | e The cassette tape used is a TYPE II (HIGH/ | eUse only TYPE I (Normal) tapes.
emphasized.
CrOz) or TYPE IV (Meta!) tapes.
e Disc is loaded with label side to the left.
No sound from speakers.
Function is not set to the desired listening
source on the receiver.
Cassette door does not open.
| eThe power cord was unplugged while
tape was running.
Cannot record.
e@Erasure prevention tabs are broken off.
yoap
a}jessey
Playback does not start.
e@Load a disc correctly with the label side (printed
side) to the right.
e@Clean the disc.
e@ Replace the disc.
@ Open and load a disc or select another disc.
e Dirt, blur, etc. on the disc.
e Disc has bad scratch or warp.
e There is no selected disc.
eStop disc play, and wait 10 seconds or more.
ePress the Stop button and wait 10 seconds or
more.
eA disc is playing.
eThe
button
was
pressed
during
disc
search or within 10 seconds after a disc
stopped playing.
The door panel does not
open
even
when
the
25
OPEN/CLOSE
button
is
pressed.
saAe|d
qa
@ The function is not set to external input | eSet the function to external input (AUX).
(AUX).
A connected CD player does
not operate.
e Antenna is not connected.
e Antenna is in poor position.
elnterference
from
nearby fluorescent
light, hair dryer,
or other
electrical
appliance.
There is no stereo sound.
eThe
MONO
indicator
in the display | ePress MONO
so that the MONO
indicator goes
window on the receiver lights up.
out, see page 26.
Timer does not work.
e Current time is not set.
Remote control unit does not | e Batteries are run down.
e@ Replace with new batteries.
work.
eA fluorescent
light is shining on the | eMove the unit away from the fluorescent light.
remote sensor window.
Sound is distorted.
e Connect the antenna correctly.
e Change antenna's position.
eStop using device causing interference.
Jouny
In the one-touch karaoke | elnterference from nearby fluorescent | eStop using the device causing interference.
mode, noise is heard when
light, hair dryer,
or other
electrical
using microphone.
appliance.
Abnormal functioning of this unit may be caused by static electricity or other external interference. To restore normal operation, turn
the power off and then on again, or unplug the AC power cord and then plug it in again.
To change the frequency step
1. Turn off the power.
The frequency step (AM: 9 kHz/10 kHz, FM: 50 kHz/100 kHz) is
2. While pressing the FREQ/STATION button, turn on the
preset depending on the area. If you need to change the step,
power.
follow the next procedure.
Repeat 1—2 to reset the frequency step.
66
<ARE7096>
En
Publicidad
