Stiga BC 500 Li 48 Manual De Instrucciones página 165

WARNING!: READ THIS MANUAL CAREFULLY BEFORE
EN
USING THE MACHINE. Keep safe for future use.
INDICE
1. GENERAL INFORMATION ..................................... 1
2. SAFETY REGULATIONS ........................................ 2
3. ABOUT THE MACHINE .......................................... 6
3.1 Machine description and intended use ........... 6
3.2 Safety signs .................................................... 7
3.3 Product identification label ............................. 7
3.4 Main components ........................................... 7
4. ASSEMBLY ............................................................. 8
4.1 Assembly components ................................... 8
4.2 Grip assembly ................................................ 8
4.3 Fitting/removing cutting means and specific
guards ............................................................ 9
4.4 FITTING OF THE BATTERY BACKPACK (if
available) ...................................................... 10
5. CONTROLS .......................................................... 10
5.1 Safety button (activation / deactivation) ....... 10
5.2 Throttle control lever ..................................... 10
5.3 Throttle safety lever ...................................... 10
6. USING THE MACHINE ......................................... 10
6.1 Preliminary operations.................................. 10
6.2 Safety checks ............................................... 11
6.3 Start-up ........................................................ 12
6.4 Operation ..................................................... 12
6.5 Operating suggestions ................................. 13
6.6 Stop.............................................................. 13
6.7 After use ....................................................... 13
7. ROUTINE MAINTENANCE ................................... 14
7.1 General Information ...................................... 14
7.2 Battery.......................................................... 14
7.3 Cleaning the machine and the engine .......... 15
7.4 Nuts and bolts .............................................. 15
8. OCCASIONAL MAINTENANCE ........................... 15
8.1 Cutting means maintenance ........................ 15
8.2 Sharpening the wire cutting blade ................ 16
9. STORAGE ............................................................. 16
9.1 Storing .......................................................... 16
9.2 Storing the battery ........................................ 16
10. HANDLING AND TRANSPORT ............................ 16
11. ASSISTANCE AND REPAIRS ............................... 16
12. WARRANTY COVERAGE ..................................... 17
13. MAINTENANCE TABLE ........................................ 17
14. TROUBLESHOOTING .......................................... 18
15. ACCESSORIES ON REQUEST ............................ 19
15.1 Batteries ....................................................... 19
15.2 Battery charger............................................. 19
15.3 Battery backpack ......................................... 19
15.4 Battery simulator .......................................... 19
1. GENERAL INFORMATION
1.1 HOW TO READ THIS MANUAL
Some of the paragraphs in this manual contain
particularly important information in terms
of safety and operation, and are highlighted
differently, according to the following criteria:
NOTE or IMPORTANT These give details
or further information on what has been
previously indicated and aim to prevent damage
to the machine or cause other damage.
The symbol highlights danger. Failure
to observe the warning can lead to possible
personal and/or third party injury and/or damage.
The paragraphs highlighted in a dotted grey
square indicate optional characteristics
not available on all models documented
in this manual. Check if the characteristics
are available on this model.
Whenever reference is made to a position on the
machine "front", "back", "left" or "right" hand side,
this refers to the operator's working position.
1.2 REFERENCES
1.2.1 Figures
The figures in these instructions for
use are numbered 1, 2, 3, etc.
Components shown in the figures
are marked A, B, C, etc.
Reference to component C in figure
2 is indicated with the wording: "See
fig. 2.C" or simply "(Fig. 2.C)".
The figures are provided by way of
example. The actual pieces can differ from
those illustrated in this document.
1.2.2 Titles
The manual is arranged in chapters and
paragraphs. The title of paragraph '2.1 Training" is
a sub-title of "2. Safety regulations". References
to titles or paragraphs are marked with the
abbreviation chap. or par. and the relevant
number. Example: "chap. 2" or "para. 2.1.
EN - 1